Jeep Liberty KJ. Manual - part 161

 

  Index      Jeep     Jeep Liberty KJ - service repair manual 2006 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  159  160  161  162   ..

 

 

Jeep Liberty KJ. Manual - part 161

 

 

POWER LOCKS

DESCRIPTION

POWER LOCKS

The power lock system allows all of the doors and the tailgate to be locked or unlocked electrically by operating a
switch on either front door trim panel. The power lock system receives non-switched battery current through a fuse
in the Junction Block (JB), so that the power locks remain operational, regardless of the ignition switch position.

The Body Control Module (BCM) locks the doors and tailgate automatically when the vehicle is driven beyond the
speed of 25.7 Km/h (15 mph), all doors are closed and the accelerator pedal is depressed. The rolling door lock
feature can be disabled if desired.

This vehicle also offers several customer programmable features, which allows the selection of several optional
electronic features to suit individual preferences.

The power lock system for this vehicle can also be operated remotely using the available Remote Keyless Entry
(RKE) system radio frequency transmitters, if equipped.

Certain functions and features of the power lock system rely upon resources shared with other electronic modules
in the vehicle over the Programmable Communications Interface (PCI) data bus network. For proper diagnosis of
these electronic modules or of the PCI data bus network, the use of a scan tool and the appropriate diagnostic
information are required.

REMOTE KEYLESS ENTRY

The RKE system allows the use of a remote battery-powered radio transmitter to signal the Body Control Module
(BCM) to actuate the power lock system. The RKE receiver operates on non-switched battery current through a fuse
in the Junction Block (JB), so that the system remains operational, regardless of the ignition switch position.

Certain RKE transmitters are also equipped with a Panic button. If the Panic button on the RKE transmitter is
depressed, the horn will sound and the exterior lights will flash on the vehicle for about three minutes, or until the
Panic button is depressed a second time. A vehicle speed of about 25.7 Km/h (15 mph) will also cancel the panic
event.

The RKE system can also perform other functions on this vehicle. If the vehicle is equipped with the optional Vehicle
Theft Security System (VTSS), the RKE transmitter will arm the VTSS when the Lock button is depressed, and
disarm the VTSS when the Unlock button is depressed.

The RKE system includes two transmitters when the vehicle is shipped from the factory, but the system can retain
the vehicle access codes of up to four transmitters. The transmitter codes are retained in the RKE receiver memory,
even if the battery is disconnected. If an RKE transmitter is faulty or lost, new transmitter vehicle access codes can
be programmed into the system using a scan tool.

This vehicle also offers several customer programmable features, which allows the selection of several optional
electronic features to suit individual preferences. Customer programmable feature options affecting the RKE system
include:

Remote Unlock Sequence - Allows the option of having only the driver side front door unlock when the RKE
transmitter Unlock button is depressed the first time. The remaining doors and the tailgate unlock when the
button is depressed a second time within 5 seconds of the first unlock press. Another option is having all doors
and the tailgate unlock upon the first depression of the RKE transmitter Unlock button.

Sound Horn on Lock - Allows the option of having the horn sound a short chirp as an audible verification that
the RKE system received a valid Lock request from the RKE transmitter, or having no audible verification. This
feature is not available on export vehicles.

Flash Lights with Lock and Unlock - Allows the option of having the lights flash as an optical verification that
the RKE system received a valid Lock request or Unlock request from the RKE transmitter, or having no opti-
cal verification.

Flip-up Glass Release - Allows the operation of a one half second press or a one second press of the rear
release button to open flip-up glass.

Programming Additional Transmitters - Allows up to four transmitter vehicle access codes to be stored in
the receiver memory. This feature is not available on export vehicles.

Certain functions and features of the RKE system rely upon resources shared with other electronic modules in the
vehicle over the Programmable Communications Interface (PCI) data bus network. For diagnosis of these electronic

8N - 66

POWER LOCKS

KJ

modules or of the PCI data bus network, the use of a scan tool and the appropriate diagnostic information are
required.

TAILGATE / FLIP-UP GLASS POWER RELEASE SYSTEM

The entire system is controlled by the Body Control Module (BCM). The tailgate / flip-up glass power release system
allows the flip-up glass latch to be released electrically by actuating a switch located integral to the outside tailgate
handle. By pulling the handle to the first detent or turning the key cylinder to unlock, the flip-up glass will open.
Pulling the handle to the second detent will allow the tailgate to open.

The tailgate / flip-up glass release system operates on non-switched battery current supplied through a fuse in the
junction block so that the system remains functional, regardless of the ignition switch position. However, the BCM
prevents the flip-up glass latch from being actuated when the tailgate latch is locked.

The tailgate will lock and can not be unlocked if the rear wiper switch is activated. The tailgate will also lock if
battery power is lost and then restored.

The tailgate/flip-up glass will not function with the battery discharged or disconnected.

COMBINATION FLASHER

This flasher can be energized by the BCM to flash all of the park/turn signal lamps as a optical alert for the RKE
panic function and, if the Flash Lights with Lock/Unlock programmable feature is enabled, as an optical verification
for the RKE lock/unlock event.

HORN RELAY

This relay can be energized by the BCM to sound the horns as an audible alert for the RKE panic function and, if
the Sound Horn on Lock programmable feature is enabled, as an audible verification for the RKE lock event.

LOW BEAM HEADLAMP RELAY

This relay can be energized by the BCM to flash the headlamp low beams as an optical alert for the RKE panic
function.

OPERATION

POWER LOCKS

The Body Control Module (BCM) locks or unlocks the doors when an actuation input signal from a door lock switch
or Remote Keyless Entry Module (RKE) is received. The BCM turns on the output drivers and provides a voltage
level to the door lock motor for a specified time. All passenger doors can be locked or unlocked using a mechanical
button mounted on the door trim panel. The front passenger doors and tailgate can be locked or unlocked by using
the key cylinder (tailgate cylinder does not lock/unlock vehicle. It only unlocks the tailgate). The tailgate will lock and
can not be unlocked if the rear wiper switch is activated (this prevents the wiper from operating when the tailgate is
ajar). The tailgate will also lock if battery power is lost and then restored.

AUTOMATIC DOOR LOCKS

When the automatic door locks are ENABLED the door locks will lock when the vehicle is moving at about 25.7
Km/h (15 mph), all doors are closed and the accelerator pedal is depressed. This feature can be switched ON or
OFF as desired. When the system is DISABLED the door locks will operate normally, but will not lock automatically
when the vehicle is rolling. Once the automatic door locks have been actuated, they will not try to lock the doors
again until a door is opened.

DOOR LOCK INHIBIT

If the key is in the ignition, in any position, and either front door is ajar, the doors can not be locked, but the unlock
function still operates. Pressing the RKE lock/unlock button under these conditions will result in a normal lock/unlock
activation.

After the key is removed from the Ignition Switch, or the doors are closed, the power door locks will operate nor-
mally.

KJ

POWER LOCKS

8N - 67

DOOR LOCK CIRCUIT PROTECTION

The BCM controls the door lock relays. If the door lock switch is actuated continuously for more than five seconds
the BCM will turn the output driver OFF (the BCM would consider the switch stuck). Each lock motor is protected
with a Positive Temperature Coefficient device that prevents motor burn out.

REMOTE KEYLESS ENTRY

LOCK: Pressing the LOCK button locks all doors, sounds horn (chirp) if enabled, and arms the Vehicle Theft
Security System, if enabled. The chirp verifies that the RKE receiver has sent a message to the BCM for door
lock operation. If a door has not been closed before pressing the LOCK button, the vehicle may not be
secured and the VTSS (if equipped) will not arm until the door is closed.

UNLOCK: Pressing the UNLOCK button once will unlock the driver’s door and activate the illuminated entry
system and disarm Vehicle Theft Security System, if equipped. Pressing the UNLOCK button twice within five
seconds will unlock all doors.

TAILGATE: Pressing the TAILGATE BUTTON unlocks the tailgate remotely and opens the flip-up glass.

PANIC: If equipped, pressing the PANIC button sounds the horns at half second intervals, flashes the exterior
lamps, and turns ON the interior lamps. The panic alarm will remain on for three minutes, or until the PANIC
button is actuated again or the ignition switch is turned to the RUN position.

The Remote Keyless Entry Module is capable of retaining the transmitter Vehicle Access Code(s) in its memory
even after vehicle power has been interrupted.

DIAGNOSIS AND TESTING - POWER LOCKS

The Body Control Module (BCM) enters a reduced power mode after the key is turned OFF. All diagnosis
and testing of the power lock system must be done with the key in the ON position unless otherwise stated.

The most reliable, efficient, and accurate means to diagnose the power lock system requires the use of a
scan tool and the proper Diagnostic Procedures manual. The scan tool can provide confirmation that the
PCI data bus is functional, that all of the electronic modules are sending and receiving the proper messages
on the PCI data bus, and that the power lock motors are being sent the proper hard wired outputs by the
relays for them to perform their power lock system functions.

Following are tests that will help to diagnose the hard wired components and circuits of the power lock system.
However, these tests may not prove conclusive in the diagnosis of this system. In order to obtain conclusive testing
of the power lock system, the Programmable Communications Interface (PCI) data bus network and all of the elec-
tronic modules that provide inputs to, or receive outputs from the power lock system components must be checked.

The Body Control Module (BCM) will set Diagnostic Trouble Codes (DTC) for the power lock system.

Refer to the appropriate wiring information. The wiring information includes wiring diagrams, proper wire and con-
nector repair procedures, details of wire harness routing and retention, connector pin-out information and location
views for the various wire harness connectors, splices and grounds.

PRELIMINARY DIAGNOSIS

As a preliminary diagnosis for the power lock system, note the system operation while you actuate both the Lock
and Unlock functions with the power lock switches and with the Remote Keyless Entry (RKE) transmitter. Then,
proceed as follows:

If the entire power lock system fails to function with either the power lock switches or the RKE transmitter,
check the fused B(+) fuse in the junction Block (JB).

If the power lock system functions with both power lock switches, but not with the RKE transmitter, proceed to
diagnosis of the Remote Keyless Entry (RKE) system. (Refer to 8 - ELECTRICAL/POWER LOCKS/KEYLESS
ENTRY TRANSMITTER - DIAGNOSIS AND TESTING) or (Refer to 8 - ELECTRICAL/POWER LOCKS/RE-
MOTE KEYLESS ENTRY MODULE - DIAGNOSIS AND TESTING).

If the power lock system functions with the RKE transmitter, but not with one or both power lock switches,
proceed to diagnosis of the door lock switches. (Refer to 8 - ELECTRICAL/POWER LOCKS/POWER LOCK
SWITCH - DIAGNOSIS AND TESTING).

If the driver side power lock switch operates only the driver side front door power lock motor, but all other
power lock motors operate with the passenger side power lock switch or the RKE transmitter, use a scan tool
and the appropriate diagnostic information to diagnose the Programmable Communications Interface (PCI)
data bus.

8N - 68

POWER LOCKS

KJ

If only one power lock motor fails to operate with both power lock switches and the RKE transmitter, proceed
to diagnosis of the power lock motor. (Refer to 8 - ELECTRICAL/POWER LOCKS/POWER LOCK MOTOR -
DIAGNOSIS AND TESTING).

KJ

POWER LOCKS

8N - 69

 

 

 

 

 

 

 

Content   ..  159  160  161  162   ..