Jeep Grand Cherokee WK. Manual - part 443

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  441  442  443  444   ..

 

 

Jeep Grand Cherokee WK. Manual - part 443

 

 

FRONT FOG LAMPS

CONDITION

POSSIBLE CAUSES

CORRECTION

FRONT FOG LAMP DOES NOT
ILLUMINATE

1. Faulty or missing fuse.

1. Test and replace front fog lamp fuse as
required.

2. Faulty or missing bulb.

2. Test and replace front fog lamp bulb as
required.

3. Faulty ground circuit.

3. Test and repair front fog lamp ground
circuit as required.

4. Faulty supply circuit.

4. Test and repair open front fog lamp relay
output circuit as required.

5. Faulty or missing relay.

5. Test and replace front fog lamp relay as
required.

6. Faulty switch.

6. Test and replace left multi-function switch
as required.

FRONT FOG LAMP DOES NOT
EXTINGUISH

1. Faulty supply circuit.

1. Test and repair shorted front fog lamp
relay output circuit as required.

2. Faulty relay.

2. Test and replace front fog lamp relay as
required.

3. Faulty switch.

3. Test and replace left multi-function switch
as required.

HAZARD WARNING LAMPS

NOTE: Before performing the following tests, confirm whether the left and right turn signals operate satis-
factorily. If the turn signals are inoperative or operate improperly, diagnose and repair that problem before
attempting to repair the Hazard Warning Lamps.

CONDITION

POSSIBLE CAUSES

CORRECTION

HAZARD WARNING LAMPS
DO NOT FLASH

1. Faulty switch.

1. Test and replace hazard switch as
required.

HAZARD WARNING LAMPS
DO NOT STOP FLASHING

1. Faulty switch.

1. Test and replace hazard switch as
required.

8L - 82

LAMPS/LIGHTING - EXTERIOR - SERVICE INFORMATION

WK

HEADLAMPS

NOTE: As part of the exterior lighting failsafe feature, upon ignition On the park lamps and the headlamp
low beams will illuminate regardless of the headlamp switch position if the instrument cluster cannot detect
an input from the headlamp switch, or if there is a loss of data bus communication.

CONDITION

POSSIBLE CAUSES

CORRECTION

HEADLAMP DOES NOT
ILLUMINATE

1. Faulty or missing bulb.

1. Test and replace headlamp bulb as
required.

2. Faulty ground circuit.

2. Test and repair open headlamp ground
circuit as required.

3. Faulty supply circuit.

3. Test and repair open headlamp low beam
or high beam circuit as required.

4. Faulty switch.

4. Test and replace left multi-function switch
as required.

HEADLAMP DOES NOT
EXTINGUISH

1. Faulty supply circuit.

1. Test and repair shorted headlamp low
beam or high beam circuit as required.

2. Faulty switch.

2. Test and replace left multi-function switch
as required.

HEADLAMPS ILLUMINATE
WITH IGNITION ON AND
HEADLAMP SWITCH OFF
(FAIL-SAFE OPERATION)

1. Faulty circuits between
headlamp switch and
instrument cluster.

1. Test and repair left multi-function switch
mux and return circuits as required.

2. Loss of data bus
communication.

2. Use a diagnostic scan tool to test the
data bus. Refer to the appropriate
diagnostic information.

3. Faulty switch.

3. Test and replace left multi-function switch
as required.

HEADLAMPS WILL NOT
SWITCH FROM HIGH TO LOW
BEAMS, OR FROM LOW TO
HIGH BEAMS

1. Faulty circuits between
multi-function switch and
instrument cluster.

1. Test and repair wash/beam select mux
and multi-function switch return circuits as
required.

2. Faulty switch.

2. Test and replace multi-function switch as
required.

AUTO HEADLAMPS
INOPERATIVE

1. Faulty circuits between sun
load sensor and instrument
cluster.

1. Test and repair sun sensor and sun
sensor return circuits as required.

2. Faulty sun load sensor.

2. Test and replace sun load sensor as
required.

WK

LAMPS/LIGHTING - EXTERIOR - SERVICE INFORMATION

8L - 83

PARK LAMPS

NOTE: As part of the exterior lighting failsafe feature, upon ignition On the exterior park lamps and the
headlamp low beams will illuminate regardless of the headlamp switch position if the instrument cluster
cannot detect an input from the headlamp switch, or if there is a loss of data bus communication.

CONDITION

POSSIBLE CAUSES

CORRECTION

PARK LAMP DOES NOT
ILLUMINATE

1. Faulty or missing fuse.

1. Test and replace park lamp fuse as
required.

2. Faulty or missing bulb.

2. Test and replace park lamp bulb as
required.

3. Faulty or missing relay.

3. Test and replace park lamp relay as
required.

4. Faulty ground circuit.

4. Test and repair open park lamp ground
circuit as required.

5. Faulty supply circuit.

5. Test and repair open park lamp relay
output circuit as required.

6. Faulty switch.

6. Test and replace left mult-function switch
as required.

PARK LAMP DOES NOT
EXTINGUISH

1. Faulty supply circuit.

1. Test and repair shorted park lamp relay
output circuit as required.

2. Faulty relay.

2. Test and replace park lamp relay as
required.

3. Faulty switch.

3. Test and replace left multi-function switch
as required.

8L - 84

LAMPS/LIGHTING - EXTERIOR - SERVICE INFORMATION

WK

SMARTBEAM

CONDITION

POSSIBLE CAUSES

CORRECTION

SMARTBEAM INOPERATIVE &
GREEN LED ON INSIDE REAR
VIEW MIRROR NOT
FLASHING

1. Automatic high beams are
not enabled.

1. Enable automatic high beams using
customer programmable features function.

2. Automatic headlamps are not
turned On.

2. Turn automatic headlamps On using the
control knob on the left multi-function switch
control stalk.

3. Vehicle speed is below 32
kilometers-per-hour (20
miles-per-hour).

3. Increase vehicle speed. SmartBeam is
not designed to operate at speeds below 32
kilometers-per-hour (20 miles-per-hour).

4. SmartBeam imager lens dirty
or obstructed.

4. Initiate the Imager Optics Test from the
Demonstration Mode to confirm the function
of the SmartBeam optics. Clean imager lens
and windshield or remove obstructions from
the windshield glass as required.

5. Faulty ground circuit.

5. Test and repair open ground circuit to
inside rear view mirror as required.

6. Faulty supply circuit.

6. Test and repair open fused run relay
output circuit to inside rear view mirror as
required.

7. Loss of data bus
communication.

7. Use a diagnostic scan tool to test the
data bus. Refer to the appropriate
diagnostic information.

8. Faulty inside rear view mirror.

8. Use a diagnostic scan tool to test the
inside rear view mirror. Refer to the
appropriate diagnostic information.

SMARTBEAM INOPERATIVE &
GREEN LED ON INSIDE REAR
VIEW MIRROR FLASHING
CONTINUALLY

1. SmartBeam calibration
required (slow flash - once-per-
second).

1. Perform the SmartBeam Calibration
procedure.

2. SmartBeam failed calibration
procedure due to improper set
up (fast flash - twice-per-
second).

2. Perform the SmartBeam Calibration
procedure properly.

3. SmartBeam failed calibration
procedure due to a mechanical
misalignment (fast flash -
twice-per-second).

3. Use a diagnostic scan tool to retrieve the
Diagnostic Trouble Code (DTC). Refer to
the appropriate diagnostic information.
Perform the appropriate SmartBeam Imager
Shim Adjustment procedure.

SMARTBEAM INOPERATIVE &
GREEN LED ON INSIDE REAR
VIEW MIRROR FLASHES
ONLY AFTER IGNITION IS
CYCLED ON

1. Three or four flashes after
cycling ignition On.

1. Internal mirror fault - electrochromic
system failure. Replace the faulty mirror as
required.

2. Five flashes after cycling
ignition On.

2. Internal mirror fault - active light sensor
system failure. Replace the faulty mirror as
required.

3. Six flashes after cycling
ignition On.

3. Internal mirror fault - SmartBeam camera
(imager) failure. Replace the faulty mirror as
required.

WK

LAMPS/LIGHTING - EXTERIOR - SERVICE INFORMATION

8L - 85

 

 

 

 

 

 

 

Content   ..  441  442  443  444   ..