Jeep Grand Cherokee WK. Manual - part 1412

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1410  1411  1412  1413   ..

 

 

Jeep Grand Cherokee WK. Manual - part 1412

 

 

U0415-IMPLAUSIBLE DATA RECEIVED

FROM ABS . . . . . . . . . . . . . . . . . . . . . . . . . . 634

U0423-IMPLAUSIBLE DATA RECEIVED

FROM CLUSTER/CCN . . . . . . . . . . . . . . . . . 636

U0424-IMPLAUSIBLE DATA RECEIVED

FROM HVAC CONTROL MODULE . . . . . . . . 638

U0431-IMPLAUSIBLE DATA FROM FCM

. . . 640

U110B-LOST ENGINE COOLANT

MESSAGE . . . . . . . . . . . . . . . . . . . . . . . . . . 642

U1118-LOST ENGINE MESSAGE

. . . . . . . . . 645

U1119-LOST FCM MESSAGE

. . . . . . . . . . . . 648

U1400-IMPLAUSIBLE TPS SIGNAL

RECEIVED . . . . . . . . . . . . . . . . . . . . . . . . . . 651

U1401-IMPLAUSIBLE ENGINE SPEED

SIGNAL RECEIVED . . . . . . . . . . . . . . . . . . . 653

U1402-IMPLAUSIBLE ENGINE

TEMPERATURE SIGNAL RECEIVED . . . . . . 655

U1404-IMPLAUSIBLE STATIC ENGINE

TORQUE SIGNAL RECEIVED . . . . . . . . . . . 657

U1405-IMPLAUSIBLE MINIMUM ENGINE

TORQUE SIGNAL RECEIVED . . . . . . . . . . . 659

U1406-IMPLAUSIBLE MAXIMUM ENGINE

TORQUE SIGNAL RECEIVED . . . . . . . . . . . 661

U1407-IMPLAUSIBLE ENGINE TORQUE

REQUEST SIGNAL RECEIVED . . . . . . . . . . . 663

U1408-IMPLAUSIBLE BRAKE SIGNAL

RECEIVED . . . . . . . . . . . . . . . . . . . . . . . . . . 665

U1409-IMPLAUSIBLE LEFT FRONT WHEEL

SPEED SIGNAL RECEIVED . . . . . . . . . . . . . 667

U140A-IMPLAUSIBLE RIGHT FRONT

WHEEL SPEED SIGNAL RECEIVED . . . . . . 669

U140B-IMPLAUSIBLE LEFT REAR WHEEL

SPEED SIGNAL RECEIVED . . . . . . . . . . . . . 671

U140C-IMPLAUSIBLE RIGHT REAR WHEEL

SPEED SIGNAL RECEIVED . . . . . . . . . . . . . 673

U140D-IMPLAUSIBLE WHEEL SPEED

SIGNALS RECEIVED . . . . . . . . . . . . . . . . . . 675

U140F-IMPLAUSIBLE ENGINE VARIANT

DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 677

U1410-IMPLAUSIBLE/MISSING FCM

VARIANT DATA . . . . . . . . . . . . . . . . . . . . . . 679

U1507-IMPLAUSIBLE ENGINE

TEMPERATURE MESSAGE DATA LENGTH
RECEIVED . . . . . . . . . . . . . . . . . . . . . . . . . . 681

U1509-IMPLAUSIBLE ENGINE VARIANT

MESSAGE DATA LENGTH RECEIVED . . . . . 683

U150A-IMPLAUSIBLE FCM VARIANT

MESSAGE DATA LENGTH RECEIVED . . . . . 685

STANDARD PROCEDURE

NAG1 PRE-DIAGNOSTIC

TROUBLESHOOTING PROCEDURE . . . . . . 687

NAG1 TRANSMISSION VERIFICATION TEST

- VER 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 688

SCHEMATICS AND DIAGRAMS

. . . . . . . . . . . 689

AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS

DIAGNOSIS AND TESTING

21 - 458

AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS

WK

P0219–ENGINE OVERSPEED

For the Transmission circuit diagram (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - NAG1 - SCHE-
MATICS AND DIAGRAMS)

For a complete wiring diagram Refer to Section 8W

Theory of Operation

The Transmission Control Module (TCM) monitors the engine speed over the CAN bus. If the engine speed is
greater than 4100+ 800 RPM, the TCM assumes that either the information from the Powertrain Control Module
(PCM) is incorrect or that a major mechanical problem exist. Once the DTC is set, the TCM will position the trans-
mission gear into neutral to protect the engine and transmissin from damage. The transmission will remain in neutral
and will not be revaluated by the TCM until the ignition is cycled.

When Monitored:
Continuously with the ignition on, engine running, with the transmission in gear with a valid Engine RPM mes-
sage received at least once, and the CAN Bus Circuit and Engine CAN Message Missing are not active.

Set Condition:
Engine speed is greater than 4100+ 800 RPM.

Possible Causes

MECHANICAL ENGINE PROBLEM

MECHANICAL TRANSMISSION PROBLEM

POWERTRAIN CONTROL MODULE

TRANSMISSION CONTROL MODULE

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 21 - TRANSMIS-
SION/TRANSAXLE/AUTOMATIC - NAG1 - STANDARD PROCEDURE)

Diagnostic Test

1.

CHECK FOR OTHER TRANSMISSION DTCS

With the scan tool, check for other transmission DTCs.

Are there any gear ratio and/or speed sensor DTCs present in addition to P0219?

Yes

>> Refer to the Symptom Category and perform the appropriate symptom. If speed sensor DTCs are

present, perform their respective test first.

No

>> Go To 2

2.

CHECK IF ENGINE MECHANICAL PROBLEMS ARE PRESENT

Determine if any Engine mechanical problems are present.

Are there any Engine mechanical problems present?

Yes

>> Repair engine as necessary. Refer to 9 - ENGINE-SERVICE INFORMATION for the appropriate repair

procedures.

No

>> Go To 3

WK

AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS

21 - 459

P0219–ENGINE OVERSPEED (CONTINUED)

3.

CHECK IF TRANSMISSION MECHANICAL PROBLEMS ARE PRESENT

Determine if any Transmission mechanical problems are present.

Turn the ignition off to the lock position.

Remove the Transmission Oil Pan and inspect for debris or a plugged Transmission Oil Filter. Refer to 21 - AUTO-
MATIC TRANSMISSION-AUTOMATIC TRANSMISSION NAG1/SERVICE INFORMATION for the appropriate service
procedures.

Is there any debris, plugged Transmission Oil Filter, or signs of an internal transmission problem?

Yes

>> Repair Transmission as necessary. Refer to 21 - AUTOMATIC TRANSMISSION-AUTOMATIC TRANS-

MISSION-NAG1/SERVICE INFORMATION for the appropriate service procedures.

No

>> Go To 4

4.

TEST DRIVE VEHICLE

NOTE: The Engine and Transmission must not have mechanical problems and be operating normally before
proceeding with this test.
Replace and program the Powertrain Control Module (PCM) per the Service Information. Refer to 8 - ELECTRICAL/
ELECTRONIC CONTROL MODULES/POWERTRAIN CONTROL MODULE for the appropriate service procedures.

Reassemble any previously disconnected connectors and/or components.

With the scan tool, erase Transmission DTCs.

Road test the vehicle.

With the scan tool, read Transmission DTCs.

Did DTC P0219-ENGINE OVERSPEED reset?

Yes

>> Using the schematics as a guide, check the Transmission Control Module (TCM) terminals for corrosion,

damage, or terminal push out. Pay particular attention to all power and ground circuits. If no problems
are found, replace the TCM per the Service Information. Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/TRANSMISSION CONTROL MODULE for the appropriate service procedures.

Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1.

No

>> Test Complete

Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1.

21 - 460

AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS

WK

P0562-BATTERY VOLTAGE LOW

WK

AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS

21 - 461

 

 

 

 

 

 

 

Content   ..  1410  1411  1412  1413   ..