Dual piston disc brake calipers are used on the front. Single piston disc brake calipers are used on the rear. Ven-
tilated disc brake rotors are used on the front and solid rotors are used on the rear.

Power brake assist is supplied by a vacuum operated, dual diaphragm power brake booster. The master cylinder
used for all applications has an aluminum body and nylon reservoir with single filler cap. A fluid level indicator is
mounted to the side of the reservoir.

The braking force of the rear wheels is controlled by electronic brake distribution (EBD). The EBD functions like a
rear proportioning valve. The EBD system uses the ABS system to control the slip of the rear wheels in partial
braking range. The braking force of the rear wheels is controlled electronically by using the inlet and outlet valves
located in the HCU.

Factory installed brake linings on all models consists of organic base material combined with metallic particles.

DIAGNOSIS AND TESTING - BASE BRAKE SYSTEM

Base brake components consist of the brake shoes, calipers, rear park brake drums/rotors, front brake rotors, brake
lines, master cylinder, booster, HCU and parking brake shoes.

Brake diagnosis involves determining if the problem is related to a mechanical, hydraulic, electrical or vacuum oper-
ated component.

The first diagnosis step is the preliminary check.

5 - 2

BRAKES - BASE - SERVICE INFORMATION

PRELIMINARY BRAKE CHECK

1. Check condition of tires and wheels. Damaged wheels and worn, damaged, or underinflated tires can cause pull,

shudder, vibration, and a condition similar to grab.

2. If complaint was based on noise when braking, check suspension components. Jounce front and rear of vehicle

and listen for noise that might be caused by loose, worn or damaged suspension or steering components.

3. Inspect brake fluid level and condition. Note that the brake reservoir fluid level will decrease in proportion to

normal lining wear. Also note that brake fluid tends to darken over time. This is normal and should not be
mistaken for contamination.

a. If fluid level is abnormally low, look for evidence of leaks at calipers, brake lines, master cylinder, and HCU.

b. If fluid appears contaminated, drain out a sample to examine. System will have to be flushed if fluid is sep-

arated into layers, or contains a substance other than brake fluid. The system seals, cups, hoses, master
cylinder, and HCU will also have to be replaced after flushing. Use clean brake fluid to flush the system.

4. Check parking brake operation. Verify free movement and full release of cables and lever. Also note if vehicle

was being operated with parking brake partially applied.

5. Check brake pedal operation. Verify that pedal does not bind and has adequate free play. If pedal lacks free play,

check pedal and power booster for being loose or for bind condition. Do not road test until condition is corrected.

6. Check booster vacuum check valve and hose.

7. If components checked appear OK, road test the vehicle.

ROAD TESTING

1. If complaint involved low brake pedal, pump pedal and note if it comes back up to normal height.

2. Check brake pedal response with transmission in neutral and engine running. Pedal should remain firm under

constant foot pressure.

3. During road test, make normal and firm brake stops in 25-40 mph range. Note faulty brake operation such as low

pedal, hard pedal, fade, pedal pulsation, pull, grab, drag, noise, etc.

4. Attempt to stop the vehicle with the parking brake only (do not exceed 25 mph) and note grab, drag, noise, etc.

PEDAL FALLS AWAY

A brake pedal that falls away under steady foot pressure is generally the result of a system leak. The leak point
could be at a brake line, fitting, hose, or caliper. If leakage is severe, fluid will be evident at or around the leaking
component.

Internal leakage (seal by-pass) in the master cylinder caused by worn or damaged piston cups, may also be the
problem cause.

An internal leak in the ABS system may also be the problem with no visual fluid leak.

LOW PEDAL

If a low pedal is experienced, pump the pedal several times. If the pedal comes back up, the most likely causes are
worn linings, rotors, or calipers are not sliding on the slide pins. The proper course of action is to inspect and
replace all worn component.

SPONGY PEDAL

A spongy pedal is most often caused by air in the system. However substandard brake hoses can cause a spongy
pedal. The proper course of action is to bleed the system, and replace substandard quality brake hoses if sus-
pected.

HARD PEDAL OR HIGH PEDAL EFFORT

A hard pedal or high pedal effort may be due to lining that is water soaked, contaminated, glazed, or badly worn.
The power booster, check valve, check valve seal/grommet or vacuum leak could also cause a hard pedal or high
pedal effort.

PEDAL PULSATION

Pedal pulsation is caused by components that are loose, or beyond tolerance limits.

BRAKES - BASE - SERVICE INFORMATION

5 - 3

The primary cause of pulsation are disc brake rotors with excessive lateral runout or thickness variation. Other
causes are loose wheel bearings or calipers and worn, damaged tires.

NOTE: Some pedal pulsation may be felt during ABS activation.

BRAKE DRAG

Brake drag occurs when the lining is in constant contact with the rotor or drum. Drag can occur at one wheel, all
wheels, fronts only, or rears only.

Drag is a product of incomplete brake release. Drag can be minor or severe enough to overheat the linings, rotors
and park brake drums.

Minor drag will usually cause slight surface charring of the lining. It can also generate hard spots in rotors and park
brake drums from the overheat-cool down process. In most cases, the rotors, wheels and tires are quite warm to the
touch after the vehicle is stopped.

Severe drag can char the brake lining all the way through. It can also distort and score rotors to the point of
replacement. The wheels, tires and brake components will be extremely hot. In severe cases, the lining may gen-
erate smoke as it chars from overheating.

Common causes of brake drag are:

•

Parking brake partially applied.

•

Loose/worn wheel bearing.

•

Seized caliper.

•

Caliper binding.

•

Loose caliper mounting.

•

Mis-assembled components.

•

Damaged brake lines.

If brake drag occurs at the front, rear or all wheels, the problem may be related to a blocked master cylinder return
port, faulty power booster (binds-does not release) or the ABS system.

BRAKE FADE

Brake fade is usually a product of overheating caused by brake drag. However, brake overheating and resulting
fade can also be caused by riding the brake pedal, making repeated high deceleration stops in a short time span,
or constant braking on steep mountain roads. Refer to the Brake Drag information in this section for causes.

BRAKE PULL

Front brake pull condition could result from:

•

Contaminated lining in one caliper

•

Seized caliper piston

•

Binding caliper

•

Loose caliper

•

Rusty caliper slide surfaces

•

Improper brake shoes

•

Damaged rotor

•

Wheel alignment.

•

Tire pressure.

A worn, damaged wheel bearing or suspension component are further causes of pull. A damaged front tire (bruised,
ply separation) can also cause pull.

A common and frequently misdiagnosed pull condition is where direction of pull changes after a few stops. The
cause is a combination of brake drag followed by fade at one of the brake units.

As the dragging brake overheats, efficiency is so reduced that fade occurs. Since the opposite brake unit is still
functioning normally, its braking effect is magnified. This causes pull to switch direction in favor of the normally
functioning brake unit.

5 - 4

BRAKES - BASE - SERVICE INFORMATION

An additional point when diagnosing a change in pull condition concerns brake cool down. Remember that pull will
return to the original direction, if the dragging brake unit is allowed to cool down (and is not seriously damaged).

REAR BRAKE DRAG OR PULL

Rear drag or pull may be caused by improperly adjusted park brake shoes or seized parking brake cables, con-
taminated lining, bent or binding shoes or improperly assembled components. This is particularly true when only one
rear wheel is involved. However, when both rear wheels are affected, the master cylinder or ABS system could be
at fault.

BRAKES DO NOT HOLD AFTER DRIVING THROUGH DEEP WATER PUDDLES

This condition is generally caused by water soaked lining. If the lining is only wet, it can be dried by driving with the
brakes very lightly applied for a mile or two. However, if the lining is both soaked and dirt contaminated, cleaning
and or replacement will be necessary.

BRAKE LINING CONTAMINATION

Brake lining contamination is mostly a product of leaking calipers or worn seals, driving through deep water puddles,
or lining that has become covered with grease and grit during repair. Contaminated lining should be replaced to
avoid further brake problems.

WHEEL AND TIRE PROBLEMS

Some conditions attributed to brake components may actually be caused by a wheel or tire problem.

A damaged wheel can cause shudder, vibration and pull. A worn or damaged tire can also cause pull.

NOTE: Propshaft angle can also cause vibration/shudder.

Severely worn tires with very little tread left can produce a grab-like condition as the tire loses and recovers traction.
Flat-spotted tires can cause vibration and generate shudder during brake operation. Tire damage such as a severe
bruise, cut, ply separation, low air pressure can cause pull and vibration.

BRAKE NOISES

Some brake noise is common on some disc brakes during the first few stops after a vehicle has been parked over-
night or stored. This is primarily due to the formation of trace corrosion (light rust) on metal surfaces. This light
corrosion is typically cleared from the metal surfaces after a few brake applications causing the noise to subside.

BRAKE SQUEAK/SQUEAL

Brake squeak or squeal may be due to linings that are wet or contaminated with brake fluid, grease, or oil. Glazed
linings and rotors with hard spots can also contribute to squeak. Dirt and foreign material embedded in the brake
lining will also cause squeak/squeal.

A very loud squeak or squeal is frequently a sign of severely worn brake lining. If the lining has worn through to the
brake shoes in spots, metal-to-metal contact occurs. If the condition is allowed to continue, rotors may become so
scored that replacement is necessary.

NOTE: The front outer brake shoes are equipped with a wear indicator. The indicator will produce an audi-
ble noise when it contacts the rotor surface.

BRAKE CHATTER

Brake chatter is usually caused by loose or worn components, or glazed/burnt lining. Rotors with hard spots can
also contribute to chatter. Additional causes of chatter are out-of-tolerance rotors, brake lining not securely attached
to the shoes, loose wheel bearings and contaminated brake lining.

THUMP/CLUNK NOISE

Thumping or clunk noises during braking are frequently not caused by brake components. In many cases, such
noises are caused by loose or damaged steering, suspension, or engine components.

BRAKES - BASE - SERVICE INFORMATION

5 - 5

Content .. 92 93 94 95 ..