Jeep Grand Cherokee WJ. Manual - part 649

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  647  648  649  650   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 649

 

 

TEST

ACTION

APPLICABILITY

2

Replace the Fuel Injection Pump in accordance with the Service Information.
With the DRB, erase ECM DTCs.
Perform several drive cycles, turning the ignition off for at least 10 seconds between
each drive cycle.
Monitor the DRB for ECM DTCs.
Did this DTC reset?

All

Yes

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

The repair is complete.
Perform ROAD TEST VERIFICATION - VER-2.

3

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform ROAD TEST VERIFICATION - VER-2.

No

Test Complete.

152

DRIVEABILITY - DIESEL

P1225-CONTROL SLEEVE SENSOR START END POS. NOT ATTAINED —

Continued

Symptom:

P1230-TIMING GOVERNING NEGATIVE GOVERNOR DEVIATION

When Monitored and Set Condition:

P1230-TIMING GOVERNING NEGATIVE GOVERNOR DEVIATION

When Monitored:

With the engine speed between 1000 and 4800 RPM.

Set Condition:

The ECM detects 3 degrees of excess timing retard for at least 10 seconds.

POSSIBLE CAUSES

CHECK FOR OTHER DTCS

ENGINE CONTROL MODULE

REPLACE THE FUEL INJECTION PUMP

INTERMITTENT CONDITION

FUEL INJECTION PUMP TIMING INCORRECT

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, erase ECM DTCs.
Turn the ignition off, wait 30 seconds, then attempt to start the engine.
With the DRB, read ECM DTCs.
Did this DTC reset?

All

Yes

Go To

2

No

Go To

5

2

NOTE: This DTC will set due to noise on the Needle Movement Sensor
circuit.
Turn the ignition on.
With the DRB, check for additional DTCs.
Are other DTCs present?

All

Yes

Refer to the Symptom List for diagnosis of the other DTCs before
continuing.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

3

3

Check the Fuel Injection Pump timing using the Service Information.
Is the Fuel Injection Pump timed correctly?

All

Yes

Go To

4

No

Reset the Fuel Injection Pump timing in accordance with the
Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

153

DRIVEABILITY - DIESEL

TEST

ACTION

APPLICABILITY

4

Replace the Fuel Injection Pump in accordance with the Service Information.
With the DRB, erase ECM DTCs.
Perform several drive cycles, turning the ignition off for at least 10 seconds between
each drive cycle.
Monitor the DRB for ECM DTCs.
Did this DTC reset?

All

Yes

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

The repair is complete.
Perform ROAD TEST VERIFICATION - VER-2.

5

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform ROAD TEST VERIFICATION - VER-2.

No

Test Complete.

154

DRIVEABILITY - DIESEL

P1230-TIMING GOVERNING NEGATIVE GOVERNOR DEVIATION —

Continued

Symptom:

P1230-TIMING GOVERNING POSITIVE GOVERNOR DEVIATION

When Monitored and Set Condition:

P1230-TIMING GOVERNING POSITIVE GOVERNOR DEVIATION

When Monitored:

With the engine speed between 1000 and 4800 RPM.

Set Condition:

The ECM detects 3 degrees of excess timing advance for at least 10

seconds.

POSSIBLE CAUSES

ENGINE CONTROL MODULE

REPLACE THE FUEL INJECTION PUMP

INTERMITTENT CONDITION

FUEL SYSTEM RESTRICTIONS

FUEL INJECTION PUMP TIMING INCORRECT

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, erase ECM DTCs.
Turn the ignition off, wait 30 seconds, then attempt to start the engine.
With the DRB, read ECM DTCs.
Did this DTC reset?

All

Yes

Go To

2

No

Go To

5

2

NOTE: This DTC will set due to low fuel volume to the Fuel Injection Pump.
Check the fuel system for restrictions.
Were any problems found?

All

Yes

Repair as necessary.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

3

3

Check the Fuel Injection Pump timing using the Service Information.
Is the Fuel Injection Pump timed correctly?

All

Yes

Go To

4

No

Reset the Fuel Injection Pump timing in accordance with the
Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

155

DRIVEABILITY - DIESEL

 

 

 

 

 

 

 

Content   ..  647  648  649  650   ..