Jeep Grand Cherokee WJ. Manual - part 624

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  622  623  624  625   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 624

 

 

Symptom:

P0123-THROTTLE POSITION SENSOR VOLTAGE HIGH

When Monitored and Set Condition:

P0123-THROTTLE POSITION SENSOR VOLTAGE HIGH

When Monitored:

With the ignition on and battery voltage above 10.4 volts.

Set Condition:

The throttle position sensor signal voltage is above 4.94 volts.

POSSIBLE CAUSES

PCM - 5-VOLT SUPPLY CIRCUIT

PCM - TP SENSOR SIGNAL CIRCUIT

INTERMITTENT CONDITION

TP SENSOR SIGNAL CIRCUIT SHORTED TO THE 5-VOLT SUPPLY CIRCUIT

VERIFY TP SENSOR OPERATION

5-VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE

TP SENSOR SIGNAL CIRCUIT OPEN

PCM SENSOR GROUND CIRCUIT OPEN

TP SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE

TP SENSOR OPEN

PCM - SENSOR GROUND OPEN

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, read PCM DTCs.
Is the Starts Since Set counter displayed and equal to 0?

All

Yes

Go To

2

No

Go To

13

2

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Turn the ignition on.
Measure the voltage of the 5-volt Supply circuit from the PCM in APP Sensor harness
connector cavity 2.
Is the voltage above 5.5 volts?

All

Yes

Go To

3

No

Go To

6

52

DRIVEABILITY - DIESEL

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Turn the ignition on.
Measure the voltage of the TP Sensor Signal circuit.
Is the voltage above 5.5 volts?

All

Yes

Go To

5

No

Go To

4

4

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Disconnect the PCM harness connectors.
Disconnect the ECM harness connectors.
Measure the resistance between the TP Sensor Signal circuit and the 5-volt Supply
circuits at cavity 2 and 10 of the APP Sensor harness connector.
Is the resistance above 100 kohms for both measurements?

All

Yes

Go To

5

No

Repair the TP Sensor Signal and 5-volt Supply circuits for a short
together.
Perform ROAD TEST VERIFICATION - VER-2.

5

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Disconnect the PCM harness connectors.
Turn the ignition on.
Measure the voltage between ground and the 5-volt Supply circuit from the PCM.
Is the voltage below 0.5 volt?

All

Yes

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Repair the 5-volt Supply circuit from the PCM for a short to
voltage.
Perform ROAD TEST VERIFICATION - VER-2.

6

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Turn the ignition on.
Measure the voltage of the TP Sensor Signal circuit.
Is the voltage above 5.5 volts?

All

Yes

Go To

7

No

Go To

8

7

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Disconnect the PCM harness connectors.
Measure the voltage between ground and the TP Sensor Signal circuit.
Is the voltage below 0.5 volt?

All

Yes

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Repair the TP Sensor Signal circuit for a short to voltage.
Perform ROAD TEST VERIFICATION - VER-2.

53

DRIVEABILITY - DIESEL

P0123-THROTTLE POSITION SENSOR VOLTAGE HIGH —

Continued

TEST

ACTION

APPLICABILITY

8

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Disconnect the PCM harness connectors.
Disconnect the ECM harness connectors.
Measure the resistance between the TP Sensor Signal circuit and the 5-volt Supply
circuits at cavity 2 and 10 of the APP Sensor harness connector.
Is the resistance above 100 kohms for both measurements?

All

Yes

Go To

9

No

Repair the TP Sensor Signal and 5-volt Supply circuits for a short
together.
Perform ROAD TEST VERIFICATION - VER-2.

9

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Disconnect the PCM harness connectors.
Measure the resistance of the TP Sensor Signal circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

10

No

Repair the TP Sensor Signal circuit for an open
Perform ROAD TEST VERIFICATION - VER-2.

10

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Disconnect the PCM harness connectors.
Measure the resistance of the Sensor Ground circuit between APP Sensor harness
connector cavity 4 and PCM harness connector C1.
Is the resistance below 5.0 ohms?

All

Yes

Go To

11

No

Repair the PCM TP Sensor Ground circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

11

Turn the ignition off.
Disconnect the APP Sensor harness connector.
NOTE: Ensure the PCM harness connectors are connected before continu-
ing.
Turn the ignition on.
With the DRB, read the TP Sensor voltage with the accelerator pedal in the at rest
position.
Connect a jumper wire between cavity 3 and cavity 4 of the APP Sensor harness
connector.
Does the DRB read below 1.0 volt?

All

Yes

Replace the Accelerator Pedal Position Sensor in accordance with
the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

12

12

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

54

DRIVEABILITY - DIESEL

P0123-THROTTLE POSITION SENSOR VOLTAGE HIGH —

Continued

TEST

ACTION

APPLICABILITY

13

Turn the ignition on.
With the DRB, read the TP Sensor volts.
With the accelerator pedal in the idle position, slowly depress the accelerator pedal
until the pedal is fully depressed.
NOTE: The TP Sensor volts should increase smoothly as the pedal is
depressed.
Does the voltage increase smoothly with the accelerator pedal travel?

All

Yes

Go To

14

No

Replace the Accelerator Pedal Position Sensor in accordance with
the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

14

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform ROAD TEST VERIFICATION - VER-2.

No

Test Complete.

55

DRIVEABILITY - DIESEL

P0123-THROTTLE POSITION SENSOR VOLTAGE HIGH —

Continued

 

 

 

 

 

 

 

Content   ..  622  623  624  625   ..