Jeep Grand Cherokee WJ. Manual - part 438

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  436  437  438  439   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 438

 

 

(9) Hold sun gear in place and install thrust plate

over sun gear at rear of driving shell (Fig. 241).

(10) Position wood block on bench and support sun

gear on block (Fig. 242). This makes it easier to align
and install sun gear lock ring. Keep wood block
handy as it will also be used for geartrain end play
check.

(11) Align rear thrust plate on driving shell and

install sun gear lock ring. Be sure ring is fully seated
in sun gear ring groove (Fig. 243).

(12) Install assembled driving shell and sun gear

on output shaft (Fig. 244).

(13) Install rear thrust washer on front planetary

gear (Fig. 245). Use enough petroleum jelly to hold
washer in place and be sure all four washer tabs are
seated.

Fig. 238 Installing Rear Planetary Front Thrust

Washer

1 – FRONT TABBED THRUST WASHER
2 – REAR PLANETARY GEAR

Fig. 239 Installing Spacer On Sun Gear

1 – SUN GEAR
2 – SUN GEAR SPACER

Fig. 240 Installing Driving Shell Front Thrust Plate

On Sun Gear

1 – SPACER
2 – SUN GEAR
3 – THRUST PLATE

Fig. 241 Installing Driving Shell Rear Thrust Plate

1 – DRIVING SHELL
2 – SUN GEAR
3 – REAR THRUST PLATE

21 - 134

42RE AUTOMATIC TRANSMISSION

WJ

DISASSEMBLY AND ASSEMBLY (Continued)

Fig. 242 Supporting Sun Gear On Wood Block

1 – SUN GEAR
2 – DRIVING SHELL
3 – WOOD BLOCK

Fig. 243 Installing Sun Gear Lock Ring

1 – LOCK RING GROOVE
2 – SUN GEAR LOCK RING
3 – DRIVING SHELL
4 – REAR THRUST PLATE

Fig. 244 Installing Assembled Sun Gear And Driving

Shell On Output Shaft

1 – SUN GEAR/DRIVING SHELL ASSEMBLY
2 – OUTPUT SHAFT

Fig. 245 Installing Rear Thrust Washer On Front

Planetary Gear

1 – FRONT PLANETARY GEAR
2 – REAR TABBED THRUST WASHER

WJ

42RE AUTOMATIC TRANSMISSION

21 - 135

DISASSEMBLY AND ASSEMBLY (Continued)

(14) Install front planetary gear on output shaft

and in driving shell (Fig. 246).

(15) Install front thrust washer on front planetary

gear. Use enough petroleum jelly to hold washer in
place and be sure all four washer tabs are seated.

(16) Assemble front annulus gear and support, if

necessary. Be sure support snap ring is seated.

(17) Install front annulus on front planetary (Fig.

246).

(18) Position thrust plate on front annulus gear

support (Fig. 247). Note that plate has two tabs
on it. These tabs fit in notches of annulus hub.

(19) Install thrust washer in front annulus (Fig.

248). Align flat on washer with flat on planetary
hub. Also be sure washer tab is facing up.

(20) Install front annulus snap ring (Fig. 249). Use

snap ring pliers to avoid distorting ring during
installation. Also be sure ring is fully seated.

(21) Install planetary selective snap ring with

snap ring pliers (Fig. 250). Be sure ring is fully
seated.

(22) Turn planetary geartrain assembly over so

driving shell is facing workbench. Then support
geartrain on wood block positioned under forward
end of output shaft. This allows geartrain compo-
nents to move forward for accurate end play check.

(23) Check planetary geartrain end play with

feeler gauge (Fig. 251). Gauge goes between shoulder
on output shaft and end of rear annulus support.

(24) Geartrain end play should be 0.12 to 1.22 mm

(0.005 to 0.048 in.). If end play is incorrect, snap ring
(or thrust washers) may have to be replaced. Snap
ring is available in three different thicknesses for
adjustment purposes.

Fig. 246 Installing Front Planetary And Annulus

Gears

1 – FRONT PLANETARY GEAR
2 – FRONT THRUST WASHER
3 – FRONT ANNULUS GEAR

Fig. 247 Positioning Thrust Plate On Front Annulus

Support

1 – FRONT ANNULUS
2 – THRUST PLATE

Fig. 248 Installing Front Annulus Thrust Washer

1 – WASHER FLAT ALIGNS WITH FLAT ON PLANETARY HUB
2 – FRONT ANNULUS THRUST WASHER
3 – TAB FACES FRONT

Fig. 249 Installing Front Annulus Snap Ring

1 – SNAP RING PLIERS
2 – FRONT ANNULUS SNAP RING

21 - 136

42RE AUTOMATIC TRANSMISSION

WJ

DISASSEMBLY AND ASSEMBLY (Continued)

OVERDRIVE UNIT

DISASSEMBLY

(1) Remove transmission speed sensor and O-ring

seal from overdrive case (Fig. 252).

(2) Remove overdrive piston thrust bearing (Fig.

253).

Fig. 250 Installing Planetary Selective Snap Ring

1 – SELECTIVE SNAP RING
2 – SNAP RING PLIERS

Fig. 251 Checking Planetary Geartrain End Play

1 – OUTPUT SHAFT
2 – REAR ANNULUS GEAR
3 – FEELER GAUGE

Fig. 252 Transmission Speed Sensor Removal/

Installation

1 – SOCKET AND WRENCH
2 – SPEED SENSOR
3 – O-RING

Fig. 253 Overdrive Piston Thrust Bearing Removal/

Installation

1 – THRUST BEARING
2 – OVERDRIVE PISTON
3 – THRUST PLATE

WJ

42RE AUTOMATIC TRANSMISSION

21 - 137

DISASSEMBLY AND ASSEMBLY (Continued)

 

 

 

 

 

 

 

Content   ..  436  437  438  439   ..