Jeep Grand Cherokee WJ. Manual - part 1133

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1131  1132  1133  1134   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1133

 

 

TEST

ACTION

APPLICABILITY

2

NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Driver Airbag.
Disconnect the Clockspring connector.
Note: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8310 black cable and jumper harness to the
Clockspring connector.
Turn Ignition On, and then reconnect the Battery.
With the DRBIII

t, read the active Airbag DTCs

Does the DRB show DRIVER SQUIB CIRCUIT SHORT?

All

Yes

Go To

3

No

Replace Clockspring.
Perform AIRBAG VERIFICATION TEST - VER 1.

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

3

NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the ACM connector.
Disconnect the Clockspring connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the Airbag System Load Tool 8310 ACM Adaptor to the Airbag Control
Module connector.
Measure the resistance between the Driver Airbag Line 1 and Line 2 at the
Clockspring connector.
Is the resistance below 10.0 Kohms?

All

Yes

Repair Driver Airbag Line 1 circuit Short to Driver Airbag Line 2
circuit.
Perform AIRBAG VERIFICATION TEST - VER 1.

No

Go To

4

Note: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.

35

AIRBAG

DRIVER SQUIB CIRCUIT SHORT - ACTIVE —

Continued

TEST

ACTION

APPLICABILITY

4

NOTE: Ensure the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: make sure the battery is disconnected
and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.

Note: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.

36

AIRBAG

DRIVER SQUIB CIRCUIT SHORT - ACTIVE —

Continued

Symptom:

DRIVER SQUIB SHORT TO BATTERY - ACTIVE

When Monitored and Set Condition:

DRIVER SQUIB SHORT TO BATTERY - ACTIVE

When Monitored:

When the ignition is on, the ACM monitors the voltage of the Driver

Squib circuits.

Set Condition:

The ACM has detected voltage on the Driver Squib circuits.

POSSIBLE CAUSES

DRIVER AIRBAG MODULE SHORT TO BATTERY

CLOCKSPRING, DRIVER AIRBAG CIRCUITS SHORT TO BATTERY

DRIVER AIRBAG LINE 1 SHORT TO BATTERY

DRIVER AIRBAG LINE 2 SHORT TO BATTERY

ACM, DRIVER AIRBAG SHORT TO BATTERY

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Driver Airbag.
NOTE: Check connectors - Clean/repair as necessary.
Connect the Airbag System Load Tool # 8310 brown cable and jumper harness to the
Driver Airbag connector.
Turn Ignition On and then reconnect the Battery.
With the DRBIII

t, read the active codes.

Does the DRB show DRIVER SQUIB CIRCUIT SHORT TO BATTERY?

All

Yes

Go To

2

No

Replace the Driver Airbag Module.
Perform AIRBAG VERIFICATION TEST - VER 1.

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

37

AIRBAG

TEST

ACTION

APPLICABILITY

2

NOTE: Ensure the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Driver Airbag.
Disconnect the Clockspring connector.
NOTE: Check connectors - Clean / repair as necessary.
Connect the Airbag System Load Tool # 8310 black cable and jumper harness to the
Clockspring connector.
Turn Ignition On and then reconnect the Battery.
With the DRBIII

t, read active DTCs.

Does the DRB show DRIVER SQUIB CIRCUIT SHORT TO BATTERY ?

All

Yes

Go To

3

No

Replace the Clockspring.
Perform AIRBAG VERIFICATION TEST - VER 1.

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

3

NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Clockspring connector.
Disconnect the ACM connector.
NOTE: Check connectors - Clean / repair as necessary.
Connect the Airbag System Load Tool # 8310 adaptor to the Airbag Control Module
connector.
Turn Ignition On and then reconnect the Battery.
Measure the voltage of the Driver Airbag Line 1 circuit between the Clockspring
connector and ground.
Is the voltage above 0.5 volts on Driver Airbag Line 1 circuit?

All

Yes

Repair Driver Airbag Line 1 circuit short to battery voltage.
Perform AIRBAG VERIFICATION TEST - VER 1.

No

Go To

4

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

38

AIRBAG

DRIVER SQUIB SHORT TO BATTERY - ACTIVE —

Continued

 

 

 

 

 

 

 

Content   ..  1131  1132  1133  1134   ..