Jeep Grand Cherokee WJ. Manual - part 1131

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1129  1130  1131  1132   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1131

 

 

Symptom:

CLUSTER MESSAGE MISMATCH - ACTIVE

When Monitored and Set Condition:

CLUSTER MESSAGE MISMATCH - ACTIVE

When Monitored:

After the MIC bulb test is completed, the ACM compares the ACM

warning lamp request (On or Off) and the MIC warning lamp state (On or Off) PCI Bus
messages. Each message is transmitted one time per second or when a change in the lamp
state occur

Set Condition:

If the ACM warning lamp request (On or Off) and the MIC warning lamp

state (On or Off) messages do not match within 3 consecutive seconds, the code will set.

POSSIBLE CAUSES

MIC, CLUSTER MESSAGE MISMATCH

ACM, CLUSTER MESSAGE MISMATCH

TEST

ACTION

APPLICABILITY

1

Note: Ensure communications with the Mechanical Instrument Cluster. If the MIC
does not communicate go to the Symptom List and select BUS +/- SIGNALS OPEN
FROM MIC.
With the DRBIII

t select PASSIVE RESTRAINTS, AIRBAG and MONITOR DIS-

PLAY.
With the DRBIII

t, read the LAMP ON BY MIC and LAMP REQ BY ACM monitors.

Cycle the ignition key and observe the LAMP ON BY MIC and LAMP REQ BY ACM
monitors for 6 to 8 seconds.
Does the

9LAMP ON BY MIC9 and 9LAMP REQ BY ACM9 monitors match?

All

YES

Go To

2

NO

Replace instrument cluster circuit board.
Perform AIRBAG VERIFICATION TEST - VER 1.

2

WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: make sure the battery is disconnected
and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

27

AIRBAG

Symptom List:

CLUSTER MESSAGE MISMATCH - STORED
DRIVER SQUIB CIRCUIT OPEN - STORED
DRIVER SQUIB CIRCUIT SHORT - STORED
DRIVER SQUIB SHORT TO BATTERY - STORED
DRIVER SQUIB SHORT TO GROUND - STORED
LOSS OF IGNITION RUN ONLY - STORED
LOSS OF IGNITION RUN-START - STORED
NO CLUSTER MESSAGE - STORED
PASSENGER SQUIB CIRCUIT OPEN - STORED
PASSENGER SQUIB CIRCUIT SHORT - STORED
PASSENGER SQUIB SHORT TO BATTERY - STORED
PASSENGER SQUIB SHORT TO GROUND - STORED
WARNING LAMP CIRCUIT OPEN - STORED

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be CLUSTER MESSAGE MIS-
MATCH - STORED.

When Monitored and Set Condition:

CLUSTER MESSAGE MISMATCH - STORED

When Monitored:

After the MIC bulb test is completed, the ACM compares the ACM

warning lamp request (On or Off) and the MIC warning lamp state (On or Off) PCI Bus
messages. Each message is transmitted one time per second or when a change in the lamp
state occur

Set Condition:

If the ACM warning lamp request (On or Off) and the MIC warning lamp

state (On or Off) messages do not match within 3 consecutive seconds, the code will set.

DRIVER SQUIB CIRCUIT OPEN - STORED

When Monitored:

When the ignition is on, the ACM monitors the resistance of the Driver

Squib circuits.

Set Condition:

The ACM has detected an open circuit or high resistance in the Driver

Squib circuits.

DRIVER SQUIB CIRCUIT SHORT - STORED

When Monitored:

When the ignition is on, the ACM monitors the resistance of the Driver

Squib circuits.

Set Condition:

The ACM has detected low resistance on the Driver Squib circuits.

DRIVER SQUIB SHORT TO BATTERY - STORED

When Monitored:

When the ignition is on, the ACM monitors the voltage of the Driver

Squib circuits.

Set Condition:

The ACM has detected high voltage on the Driver Squib circuits.

28

AIRBAG

DRIVER SQUIB SHORT TO GROUND - STORED

When Monitored:

When the ignition is on, the ACM monitors the voltage of the Driver

Squib circuits.

Set Condition:

The ACM has detected a short to ground in the Driver Squib circuits.

LOSS OF IGNITION RUN ONLY - STORED

When Monitored:

With the ignition in the run/start position the ACM monitors the Fused

Ignition Switch Output Run/Start circuit for proper system voltage.

Set Condition:

If the voltage on the Fused Ignition Switch Output Run Only circuit drops

below 4.5 volts, the code will set.

LOSS OF IGNITION RUN-START - STORED

When Monitored:

With the ignition in the run/start position the ACM monitors the Fused

Ignition Switch Output Run/Start circuit for proper system voltage.

Set Condition:

If the voltage on the Fused Ignition Switch Output Run/Start circuit drops

below 4.5 volts, the code will set.

PASSENGER SQUIB CIRCUIT OPEN - STORED

When Monitored:

With the ignition is On, the ACM monitors the resistance of the

Passenger Squib circuits.

Set Condition:

The ACM has detected an open circuit or high resistance on the Driver

Squib circuits.

PASSENGER SQUIB CIRCUIT SHORT - STORED

When Monitored:

When the ignition is on, the ACM monitors the resistance of the

Passenger Squib circuits.

Set Condition:

The ACM has detected low resistance in the Passenger Squib circuits.

PASSENGER SQUIB SHORT TO BATTERY - STORED

When Monitored:

When the ignition is on, the ACM monitors the voltage of the Passenger

Squib circuits.

Set Condition:

The ACM has detected high voltage on the Passenger Squib circuits.

PASSENGER SQUIB SHORT TO GROUND - STORED

When Monitored:

Continuously with the ignition on.

Set Condition:

The ACM has detected a short to ground in the Passenger Squib circuits.

WARNING LAMP CIRCUIT OPEN - STORED

When Monitored:

When the ignition is On, the ACM monitors the PCI Bus for a message

from the MIC containing the airbag warning lamp status Ok or Open. The MIC transmit
the message one time per second in response to the ACM lamp On/Off message.

Set Condition:

The code is set if the lamp state is open for 2 consecutive messages or 2

seconds.

29

AIRBAG

CLUSTER MESSAGE MISMATCH - STORED —

Continued

POSSIBLE CAUSES

ACTIVE OR STORED CODE PRESENT

STORED CODE OR INTERMITTENT CONDITION

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure the battery is fully charged.
Active codes must be resolved before diagnosing stored codes.
Turn the ignition on.
With the DRBIII

t, record and erase all DTCs from all modules.

With the DRB III monitor active codes as you work through the system.
Wiggle the wiring harness and connectors of the Airbag System and rotate the
steering wheel from stop to stop.
NOTE: Check connectors - Clean and repair as necessary.
You have just attempted to simulate the condition that initially set the trouble code
message.
The following additional checks may assist you in identifying a possible intermittent
problem:
- Visually inspect related wire harness connectors. Look for broken, bent, pushed out,
spread, corroded, or contaminated terminals.
- Visually inspect the related harnesses. Look for chafed, pierced, pinched or partially
broken wire.
- Refer to Wiring Diagrams and Technical Service Bulletins that may apply.
Did the DTCs become active?

All

Yes

Select appropriate active symptom from Symptom List.

No

No problem found at this time. Erase all codes before returning
vehicle to customer.

30

AIRBAG

CLUSTER MESSAGE MISMATCH - STORED —

Continued

 

 

 

 

 

 

 

Content   ..  1129  1130  1131  1132   ..