Jeep Grand Cherokee WJ. Manual - part 1091

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1089  1090  1091  1092   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1091

 

 

TEST

ACTION

APPLICABILITY

9

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace the Transmission Control Module. WITH THE DRBIII

t

PERFORM QUICK LEARN.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

10

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace the Line Pressure Sensor.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

11

Perform a visual inspection of all connectors, wiring, and cooler connections before
proceeding. Repair as necessary.
Check the Transmission Fluid Level per Service Information. Adjust if necessary.
With the DRBIII, Check the STARTS SINCE SET counter.
NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

45RFE AUTO

TRANS

Yes

Go To

12

No

Go To

21

12

Turn the ignition off to the lock position.
Remove the Starter Relay.
NOTE: Failure to remove the Starter Relay can cause a TCM - No Response
condition.
Install Transmission simulator Miller tool# 8333.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the DRBIII

t, monitor the 2C Pressure Switch state.

With the Transmission Simulator Miller tool# 8333, place the selector switch on 2C.
While pressing the Pressure Switch test button, wiggle the wiring harness and
connectors pertaining to the 2C Pressure Switch.
Did the 2C Pressure Switch state change to closed and remain closed while wiggling
the wires?

45RFE AUTO

TRANS

Yes

Go To

13

No

Go To

16

123

TRANSMISSION

P1728-2C HYDRAULIC PRESSURE TEST FAILURE —

Continued

TEST

ACTION

APPLICABILITY

13

The transmission must be at operating temperature prior to checking fluid level.
Adjusting fluid level on a cold transmission will result in an overfilled transmission.
Check the transmission fluid level per the Service Information.
NOTE: The transmission must be hot when checking oil level. When the
temperature is below 10 degrees C or 50 degrees F, it is possible that no oil
will show on the dipstick, even though the transmission has an adequate fill
level when warm.
Is the fluid level OK?

45RFE AUTO

TRANS

Yes

Go To

14

No

Low fluid level can be the cause of many transmission problems.
If the fluid level is low locate and repair the leak then check and
adjust the fluid level per the service information.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

14

Remove and inspect transmission oil pan per service information.
Does it contain excessive debris or contamination?

45RFE AUTO

TRANS

Yes

Repair cause of excessive debris in Transmission Oil Pan.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

15

15

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

If the transmission is to be repaired, disassemble and inspect the
Valve Body per service information and repair or replace as
necessary. If no problems are found in the valve body, replace the
Solenoid/TRS assembly.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

16

Turn the ignition off to the lock position.
Disconnect the Transmission Control Module harness connector.
Disconnect the Transmission Solenoid /TRS harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the 2C Pressure Switch Sense circuit from the Transmis-
sion Control Module harness connector to the Solenoid/TRS harness connector.
Is the resistance above 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair the 2C Pressure Switch Sense circuit for an open.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

17

124

TRANSMISSION

P1728-2C HYDRAULIC PRESSURE TEST FAILURE —

Continued

TEST

ACTION

APPLICABILITY

17

Turn ignition off to the lock position.
Disconnect the Transmission Solenoid/TRS harness connector.
Using a 12-volt test light connected to ground, check the Transmission Relay Output
circuit in the Solenoid/TRS harness connector.
Note: The light must illuminate brightly, if it does not light, or lights dimly,
the circuit must be repaired. If there is any doubt, compare the brightness
when testing the circuit, to the brightness when connected directly to the
battery positive post.
Does the light illuminate brightly?

45RFE AUTO

TRANS

Yes

Go To

18

No

Repair cause of unlit or dim test light. Open circuit or high
resistance in Transmission Relay Output circuit.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

18

Turn the ignition off to the lock position.
Disconnect the Transmission Control Module harness connector.
Disconnect the Transmission Solenoid/TRS harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the 2C Pressure Switch Sense circuit and ground.
Is the resistance below 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair the 2C Pressure Switch circuit for a short to ground.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

19

19

Turn the ignition off to the lock position.
Disconnect the Transmission Control Module harness connector.
Disconnect the Transmission Solenoid/TRS harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Relay
Output circuit in the Transmission Relay connector.
Ignition on, engine not running.
Measure the voltage of the 2C Pressure Switch Sense circuit in the Transmission
Control Module harness connector.
Is the voltage above 1.0 volt?

45RFE AUTO

TRANS

Yes

Repair the 2C Pressure Switch Sense circuit for a short to voltage.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

20

20

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace the Transmission Control Module. WITH THE DRBIII

t

PERFORM QUICK LEARN.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

125

TRANSMISSION

P1728-2C HYDRAULIC PRESSURE TEST FAILURE —

Continued

TEST

ACTION

APPLICABILITY

21

The conditions necessary to set this DTC are not present at this time. Using the
schematics as a guide, inspect the wiring and connectors specific to this circuit.
Wiggle the wires while checking for shorts and open circuits.
Were any problems found?

45RFE AUTO

TRANS

Yes

Repair as necessary.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Test Complete.

126

TRANSMISSION

P1728-2C HYDRAULIC PRESSURE TEST FAILURE —

Continued

 

 

 

 

 

 

 

Content   ..  1089  1090  1091  1092   ..