Jeep Grand Cherokee WJ. Manual - part 1085

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1083  1084  1085  1086   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1085

 

 

Symptom:

P1722-LINE PRESSURE LOW

When Monitored and Set Condition:

P1722-LINE PRESSURE LOW

When Monitored:

Continuously while driving in a forward gear.

Set Condition:

The TCM continuously monitors Actual Line Pressure and compares it to

Desired Line Pressure. If Actual Line Pressure is more than 10 PSI below Desired Line
Pressure, this code will be set.

POSSIBLE CAUSES

CHECK FOR RELATED DTC’S

INTERMITTENT WIRING & CONNECTORS CONDITIONS

INCORRECT FLUID LEVEL

5 VOLT SUPPLY CIRCUIT OPEN

5-VOLT SUPPLY OPEN - LINE PRESSURE STEADY

POOR LPS CONNECTION

5 VOLT SUPPLY CIRCUIT SHORT TO GROUND

5 VOLT SUPPLY CIRCUIT SHORT TO VOLTAGE

PCS CONTROL CIRCUIT SHORT TO VOLTAGE

PLUGGED FILTER

INTERNAL TRANSMISSION PROBLEM - LINE PRESSURE LOW

LINE PRESSURE SENSOR - CALIBRATION OUT OF LIMITS

TCM - LINE PRESSURE STEADY

99

TRANSMISSION

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0705 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

45RFE AUTO

TRANS

Continue

Go To

2

2

With the DRBIII

t, check for other transmission DTC’s

Is P1721 present also?

45RFE AUTO

TRANS

Yes

Refer to symptom list for problems related to P1721.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

3

3

The transmission temperature must be at least 180 degrees for the results of this test
to be valid.
Start the engine in park.
Raise engine speed to 2000 RPM.
With the DRBIII

t, observe the transmission Line Pressure.

Let engine speed return to idle.
Pick the answer that matches your observation.

45RFE AUTO

TRANS

Pressure below 110 PSI

Go To

4

Pressure steady between 85 and 95 PSI.

Go To

12

Pressure above 110 PSI

Go To

15

4

The transmission must be at operating temperature prior to checking fluid level.
Adjusting fluid level on a cold transmission will result in an overfilled transmission.
Check the transmission fluid level per the service information
Is the fluid level OK?

45RFE AUTO

TRANS

Yes

Go To

5

No

Adjust fluid level. Repair cause of incorrect fluid level.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

100

TRANSMISSION

P1722-LINE PRESSURE LOW —

Continued

TEST

ACTION

APPLICABILITY

5

Turn ignition switch to the lock position
Disconnect the TCM harness connector.
Disconnect the Line Pressure Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the 5 Volt Supply circuit from the Line Pressure Sensor
connector to the TCM connector.
Is the resistance above 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair open 5 Volt Supply circuit
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

6

6

Remove and inspect the transmission oil pan per service information.
Remove and inspect the primary oil filter per service information.
Does the oil pan contain excessive debris and/or is the primary oil filter plugged?

45RFE AUTO

TRANS

Yes

Repair cause of plugged transmission oil filter.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

7

7

Turn ignition switch to the lock position.
Disconnect the TCM harness connector.
Disconnect the Line Pressure Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the 5 Volt Supply circuit and ground.
Is the resistance Below 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair 5 Volt Supply circuit short to ground.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

8

8

Turn the ignition switch to the lock position.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay.
Place a jumper wire between the Fused B(+) and the Transmission Relay Output
circuits in the relay connector.
Turn ignition on.
Note: Check connectors - Clean/repair as necessary.
Measure the voltage of the 5 Volt Supply circuit in the TCM connector.
Is the voltage above 5.5 volts?

45RFE AUTO

TRANS

Yes

Repair 5 Volt Supply circuit short to voltage.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

9

101

TRANSMISSION

P1722-LINE PRESSURE LOW —

Continued

TEST

ACTION

APPLICABILITY

9

Turn ignition off to the lock position.
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/TRS harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B(+) circuit and the Trans Relay Output
circuit in the relay connector.
Turn ignition switch on.
Measure the voltage of the Pressure Control Solenoid control circuit in the TCM
connector.
Is the voltage above 3.0 volts?

45RFE AUTO

TRANS

Yes

Repair PCS Control circuit short to voltage.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

10

10

Turn ignition off to the lock position.
Install Miller Tool# 8259 per the service information.
Install a 0 to 300 PSI gauge on the tool.
Start the engine in park.
With the DRBIII

t compare the line pressure reading of the DRBIIIt with the line

pressure reading on the pressure gauge.
Is the pressure gauge reading within 34 kpa 5 PSI of the DRBIII

t reading?

45RFE AUTO

TRANS

Yes

Go To

11

No

Replace the Line Pressure Sensor.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

11

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Repair internal transmission problem as required per current
warranty policy. If the transmission is to be repaired, inspect the
oil pump per service information and replace if necessary. If no
problem is found, replace the Solenoid/TRS assembly.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

12

Ignition on, engine not running.
With the DRBIII

t, observe the Line Pressure, firmly push the line pressure sensor

connector towards the Transmission.
Did the Actual Line Pressure change to about 30 PSI when the sensor connector was
pushed?

45RFE AUTO

TRANS

Yes

Disconnect and properly reconnect the Line Pressure Sensor
connector. Inspect terminals and repair as necessary.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

13

102

TRANSMISSION

P1722-LINE PRESSURE LOW —

Continued

 

 

 

 

 

 

 

Content   ..  1083  1084  1085  1086   ..