Jeep Grand Cherokee WJ. Manual - part 1084

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1082  1083  1084  1085   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1084

 

 

Symptom:

P1721-LINE PRESSURE SENSOR FAULT

When Monitored and Set Condition:

P1721-LINE PRESSURE SENSOR FAULT

When Monitored:

Continuously with engine running.

Set Condition:

If the Line Pressure Sensor (LPS) voltage is below 0.2 volts or above 4.75

volts the code will be set.

POSSIBLE CAUSES

INTERMITTENT WIRING AND/OR CONNECTORS

5-VOLT SUPPLY CIRCUIT OPEN

GROUND CIRCUIT OPEN

LINE PRESSURE SENSOR SIGNAL CIRCUIT OPEN

5-VOLT SUPPLY CIRCUIT SHORT TO GROUND

LINE PRESSURE SENSOR SIGNAL CIRCUIT SHORT TO GROUND

LINE PRESSURE SENSOR SIGNAL CIRCUIT SHORT TO VOLTAGE

LINE PRESSURE SENSOR

TCM - HIGH LINE PRESSURE SENSOR

TCM - LOW LINE PRESSURE SENSOR

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0705 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

45RFE AUTO

TRANS

Continue

Go To

2

95

TRANSMISSION

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, Check the Line Pressure Sensor Voltage

Is the Line Pressure Sensor voltage between 0.2 and 4.75 volts?

45RFE AUTO

TRANS

Yes

Go To

3

No

Go To

4

3

The conditions necessary to set this DTC are not present at this time. Using the
schematics as a guide, inspect the wiring and connectors specific to this circuit.
Wiggle the wires while checking for shorts and open circuits.
Were any problems found?

45RFE AUTO

TRANS

Yes

Repair as necessary.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Test Complete.

4

Turn ignition off to the lock position.
Remove the Starter Relay.
NOTE: Failure to remove the Starter Relay can cause a TCM - No Response
condition.
Install Transmission Simulator Miller tool #8333.
Ignition on, engine not running.
With the DRBIII

t, monitor the Line Pressure.

Using the Transmission Simulator, set the rotary knob to each of the 3 line pressure
positions.
Note: With the DRBIII

t, monitor the line pressure sensor voltage readings, the

readings should be within 0.25 volts of the voltage reading specified on simulator.
What is the Line Pressure Sensor Voltage?

45RFE AUTO

TRANS

Below 0.2 volts.

Go To

5

Between .2 and 4.75 Volts

Go To

9

Above 4.75 Volts

Go To

10

5

Turn ignition switch to the lock position
Disconnect the TCM harness connector.
Disconnect the Line Pressure Sensor connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the 5-Volt Supply circuit from the Line Pressure Sensor
connector to the TCM connector.
Is the resistance above 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair open 5-Volt Supply circuit
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

6

96

TRANSMISSION

P1721-LINE PRESSURE SENSOR FAULT —

Continued

TEST

ACTION

APPLICABILITY

6

Turn ignition switch to the lock position.
Disconnect the TCM harness connector.
Disconnect the Line Pressure Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the 5-Volt Supply circuit and ground.
Is the resistance Below 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair 5-Volt Supply circuit short to ground.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

7

7

Turn ignition switch to the lock position.
Disconnect the TCM harness connector.
Disconnect the Line Pressure Sensor connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the Line Pressure Sensor Signal circuit and ground.
Is the resistance Below 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair Line Pressure Sensor Signal circuit short to ground.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

8

8

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace the TCM. WITH THE DRBIII

t PERFORM QUICK

LEARN.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

9

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace the Line Pressure Sensor.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

10

Turn ignition switch to the lock position
Disconnect the TCM harness connector.
Disconnect the Line Pressure Sensor connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Ground circuit from the Line Pressure Sensor
connector to the TCM connector.
Is the resistance above 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair open Ground circuit
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

11

97

TRANSMISSION

P1721-LINE PRESSURE SENSOR FAULT —

Continued

TEST

ACTION

APPLICABILITY

11

Turn ignition switch to the lock position
Disconnect the TCM harness connector..
Disconnect the Line Pressure Sensor connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Line Pressure Sensor Signal circuit from the Line
Pressure Sensor connector to the TCM connector.
Is the resistance above 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair open Line Pressure Sensor Signal circuit
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

12

12

Turn the ignition switch to the lock position.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B(+) and the Transmission Relay Output
circuits in the relay connector.
Turn ignition on.
Measure the voltage of the Line Pressure Sensor Signal circuit in the TCM connector.
Is the voltage above 5.5 volts?

45RFE AUTO

TRANS

Yes

Repair the Line Pressure Sensor Signal circuit short to voltage.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

13

13

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace the TCM. WITH THE DRBIII

t PERFORM QUICK

LEARN.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

98

TRANSMISSION

P1721-LINE PRESSURE SENSOR FAULT —

Continued

 

 

 

 

 

 

 

Content   ..  1082  1083  1084  1085   ..