Jeep Grand Cherokee WJ. Manual - part 1005

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1003  1004  1005  1006   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1005

 

 

Symptom:

P1696-PCM FAILURE EEPROM WRITE DENIED

POSSIBLE CAUSES

PCM FAILURE

Repair Instructions:

PCM FAILURE

Replace and program the Powertrain Control Module in accordance with the Service

Information.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

237

DRIVEABILITY - GAS

Symptom:

P1698-NO BUS MESSAGE FROM TCM

POSSIBLE CAUSES

PCM PCI BUS CIRCUIT OPEN

WIRING HARNESS INTERMITTENT PROBLEM

TEST

ACTION

APPLICABILITY

1

Turn ignition on, Engine not running.
With the DRBIII

t, read DTCs.

Is the Good Trip counter for DTC P1698 displayed and equal to Zero?

All

Yes

Go To

2

No

Go To

4

Note: This DTC could have been set when the TCM is disconnected for
transmission Diagnostics.

2

Turn ignition on, Engine not running.
Connect the DRBIII

tI and access Powertrain Control Module.

Note: This test checks for other PCI BUS codes. That indicates diferent
circuits in the BUS.
With the DRBIII

t, read DTCs.

Is a DTC also set for NO SKIM BUS MESSAGE and/or No MIC BUS MESSAGE?

All

Yes

Go To

3

No

Go To

3

238

DRIVEABILITY - GAS

TEST

ACTION

APPLICABILITY

3

With the DRBIII

t, read DTCs. This is to ensure power and grounds to the PCM are

operational.
NOTE: If the DRBIII

will not read PCM DTC’s, follow the (NO RESPONSE

TO PCM (SCI only)

symptom path, if vehicle will start. For NO START

Conditions follow symptom

(NO RESPONSEin Starting category .

Turn the ignition off.
Disconnect the PCM harness connector(s).
Connect the DRBIII

t to the Data Link connector

Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRBIII

t. Attach

the red and black leads and the cable to probe adapter to the scope input cable.
Select DRBIII

t Standalone.

Select lab scope.
Select Live.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again
when complete.
Connect the Black lead to the PCM ground. Connect the Red lead to the PCM PCI
Bus circuit
Turn the ignition on.
Observe the voltage displayed on the DRBIII

t Lab Scope.

What is the voltage displayed on the scope?

All

Pulse from 0 to approximately 7.5 volts

Test Complete.

Steady 0 volts

Repair the open PCI Bus circuit to PCM.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

4

Turn ignition off.
Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
Note: Visually inspect the related wire harness connectors. Look for broken,
bent, pushed out, or corroded terminals.
Note: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?

All

Yes

Repair wiring harness/connectors as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

Test Complete.

239

DRIVEABILITY - GAS

P1698-NO BUS MESSAGE FROM TCM —

Continued

Symptom:

P1899-P/N SWITCH PERFORMANCE

POSSIBLE CAUSES

INTERMITTENT PARK/NEUTRAL SWITCH SENSE CIRCUIT

PARK/NEUTRAL POSITION SWITCH

PARK/NEUTRAL SWITCH SENSE CIRCUIT OPEN

PARK/NEUTRAL SWITCH SENSE CIRCUIT SHORTED TO GROUND

POWERTRAIN CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, read DTCs.

Is the Good Trip Counter for P-1899 displayed and equal to 0?

All

Yes

Go To

2

No

Go To

7

2

Turn the ignition on.
With the DRBIII

t, read the PNP switch input state.

While moving the gear selector through all gear positions (Park to 1st and back to
Park), watch the DRB display.
Did the DRBIII

t display P/N and D/R in the correct gear positions?

All

Yes

Test Complete.

No

Go To

3

3

Turn the ignition off.
Disconnect the PCM C1 harness connector.
Disconnect the PNP switch harness connector.
Check connectors - Clean/repair as necessary
Measure the resistance of the PNP switch sense circuit between the PCM C1 harness
connector and the PNP switch harness connector.
Is the resistance below 5.0 ohms?

All

Yes

Go To

4

No

Repair the PNP switch sense circuit for an open.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

4

Turn the ignition off.
Disconnect the PCM C1 harness connector.
Disconnect the PNP switch harness connector.
Check connectors - Clean/repair as necessary
Measure the resistance between ground and the PNP switch sense circuit.
Is the resistance below 5.0 ohms?

All

Yes

Repair the PNP switch sense circuit for a short to ground.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

No

Go To

5

240

DRIVEABILITY - GAS

 

 

 

 

 

 

 

Content   ..  1003  1004  1005  1006   ..