Infiniti G35 (V35) Sedan. Manual - part 388

TRUNK LID

DLK-213

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

TRUNK LID

TRUNK LID ASSEMBLY

TRUNK LID ASSEMBLY : Exploded View

INFOID:0000000000961281

REMOVAL

ADJUSTMENT

1.

Trunk lid hinge stopper

2.

Trunk lid stay

3.

Trunk lid hinge

4.

Trunk lid assembly

5.

Bumper rubber

Refer to 

GI-4, "Components"

 for the symbols in the figure.

JMKIA0043GB

DLK-214

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

TRUNK LID

TRUNK LID ASSEMBLY : Removal and Installation

INFOID:0000000000961282

REMOVAL

1.

Remove trunk lid finisher. Refer to 

INT-27, "Removal and Installation"

.

2.

Disconnect the connectors in the trunk lid, and remove the harness clamps to pull the harness out of the
trunk lid.

3.

Insert flat-bladed screwdriver into the gap and remove holder.

4.

Remove trunk lid stay.

WARNING:

Body injury may occur if no supporting rod is holding the trunk lid open when removing the
damper stay.

5.

Remove the trunk lid hinge mounting bolts on trunk lid side and remove the trunk lid assembly.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

1.

Trunk lid assembly

2.

Bumper rubber

3.

Trunk lid hinge

4.

Trunk lid striker

5.

Rear fender

6.

Rear combination lamp

7.

Back up lamp

8.

Rear bumper

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA0044GB

TRUNK LID

DLK-215

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

• After installing, apply touch-up paint (the body color) onto the head of the hinge mounting bolts.
• After installing, check operation.
• After installing, perform fitting adjustment. Refer to 

DLK-215, "TRUNK LID ASSEMBLY : Adjust-

ment"

.

TRUNK LID ASSEMBLY : Adjustment

INFOID:0000000000961283

1.

Check the clearance and the evenness between the trunk lid and each part visually and by touching. (Fit-
ting standard dimension in the table below should be satisfied.)

* Unit: mm (in)

2.

In case out of specification, adjust them according to the procedures shown below.

3.

Loosen the bumper rubber.

4.

Loosen the striker mounting bolts.

5.

Lift up the trunk lid approximately 100 – 150 mm (3.94 – 5.91 in) height then close it lightly and check that
it is engaged firmly with the trunk lid closed.

6.

Check the clearance and evenness.

7.

Finally tighten the trunk lid striker.

TRUNK LID LOCK

TRUNK LID LOCK : Exploded View

INFOID:0000000000961284

Parts

Portion

Standard

Right/left clearance 

(MAX)

Trunk lid – 

Rear fender

A – A

E

Clearance

2.5 – 4.5 

(0.098 – 0.177)

1.5 (0.059)

F

Surface height

−

1.5 – 0.5 

(0.059 – 0.020)

1.5 (0.059)

Trunk lid – 

Rear combination lamp

B – B

G

Clearance

3.9 – 7.1 

(0.154 – 0.280)

2.1 (0.083)

H

Surface height

−

2.1 – 0.9 

(

−

0.083 – 0.035)

2.0 (0.079)

Trunk lid – 

Back–up lamp

C – C

I

Clearance

1.7 – 3.7

(0.067 – 0.146)

1.2 (0.047)

J

Surface height

−

1.8 – 0.6

(

−

0.071 – 0.024)

1.5 (0.059)

Trunk lid – 

Rear bumper

D – D

K

Clearance

4.0 – 8.0

(0.157 – 0.315)

—

DLK-216

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

TRUNK LID

TRUNK LID LOCK : Removal and Installation

INFOID:0000000000961285

REMOVAL

1.

Remove the trunk lid finisher. Refer to 

INT-27, "Removal and Installation"

.

2.

Remove the trunk lid emergency opener lever.

3.

Disconnect the trunk lid opener cable.

4.

Disconnect the connector from trunk lid lock.

5.

Remove the mounting bolts, and remove the trunk lid lock.

INSTALLATION

Install in the reverse order of removal.
NOTE:
• After installing, perform trunk lid fitting adjustment. Refer to refer to 

DLK-215, "TRUNK LID ASSEMBLY :

Adjustment"

.

• After installing, check the operation.

TRUNK LID WEATHERSTRIP

TRUNK LID WEATHERSTRIP : Exploded View

INFOID:0000000000961286

1.

Trunk lid emergency opener lever

2.

Trunk lid emergency opener lever 
holder

3.

Trunk lid opener cable

4.

Trunk lid lock

5.

Trunk lid striker

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA0045GB