Infiniti G35 (V35) Sedan. Manual - part 382

PRE-INSPECTION FOR DIAGNOSTIC

DLK-189

< ON-VEHICLE MAINTENANCE >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

YES

>> GO TO 9.

NO

>> Refer to 

DLK-51, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"

.

9.

CHECK HAZARD AND BUZZER REMINDER FUNCTION BY REQUEST SWITCH

Check hazard and buzzer reminder function by operating following switches.
• Door request switches
• Trunk opener request switch

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Refer to 

DLK-177, "Symptom Table"

.

10.

CHECK HAZARD AND HORN REMINDER FUNCTION BY INTELLIGENT KEY BUTTON

Check hazard and horn reminder function by operating Intelligent Key button.
Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Refer to

DLK-178, "Symptom Table"

.

11.

CHECK WARNING FUNCTION

Check warning function operate properly. Refer to 

DLK-173, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Refer to 

DLK-173, "Symptom Table"

.

12.

CHECK OUT

CHECK OUT.

>> INSPECTION END

DLK-190

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

HOOD

ON-VEHICLE REPAIR

HOOD

HOOD ASSEMBLY

HOOD ASSEMBLY : Exploded View

INFOID:0000000000961261

REMOVAL

ADJUSTMENT

1.

Hood hinge cover

2.

Hood stay

3.

Hood hinge

4.

Hood assembly

5.

Hood bumper rubber

6.

Seal

7.

Radiator core seal

8.

Hood insulator

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA0038GB

HOOD

DLK-191

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

HOOD ASSEMBLY : Removal and Installation

INFOID:0000000000961262

CAUTION:

Operate with two workers, because of its heavy weight.

REMOVAL

1.

Support the hood lock assembly with a proper material to prevent it from falling.

WARNING:

Body injury may occur if no supporting rod is holding the hood open when removing the hood
stay.

2.

Remove the hood hinge cover (RH,LH).

3.

Remove the washer nozzle and hose nozzle. Refer to 

WW-82, "Removal and Installation"

.

4.

Remove the stud balls on the hood stays at the hood side.

5.

Remove the hinge mounting nuts on the hood to remove the hood assembly.

6.

Remove following parts after removing the hood assembly. 
• Radiator core seal
• Hood insulator

1.

Hood assembly

2.

Striker

3.

Hood bumper rubber

4.

Hood hinge

5.

Front bumper

6.

Front fender

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA0039GB

DLK-192

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

HOOD

• Hood bumper rubber

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Before installing hood hinge, apply anticorrosive agent onto the mounting surface of the vehicle

body.

• After installing, perform hood fitting adjustment. Refer to 

DLK-192, "HOOD ASSEMBLY : Adjust-

ment"

.

HOOD ASSEMBLY : Adjustment

INFOID:0000000000961263

1.

Check the clearance and the surface height between the hood and each part visually and by touching.
(Fitting standard dimension in the table below should be satisfied.)

* Unit: mm (in)

2.

In case out of specification, adjust them according to the procedures shown below.

3.

Remove the striker and adjust the surface height of hood, front bumper and front fender according to the
fitting standard dimension, by rotating hood bumper rubbers. 

4.

Adjust the clearance of striker, hood bumper rubber according to the fitting standard dimension. 

5.

Loosen the hood hinge mounting nuts on the hood.

6.

Adjust the clearance of hood, front bumper and front fender according to the fitting standard dimension,
for the hood.

7.

Check that the hood lock primary latch is securely engaged with the striker by dropping hood from approx-
imately 200 mm (7.87 in) height or pressing lightly on the hood.

CAUTION:

Do not drop hood from a height of 300 mm (11.81 in) or more.

8.

Install as static closing face of hood is 94 – 490 N·m (9.6 – 50.0 kg-m).
NOTE:
• Exercise vertical force on right side and left side of hood lock.
• Do not press simultaneously both sides.

9.

After adjustment tighten hood hinge mounting nuts to the specified torque.

HOOD LOCK CONTROL

HOOD LOCK CONTROL : Exploded View

INFOID:0000000000961264

Parts

Standard

Right/left clear-

ance (MAX)

Hood – Front 
bumper

A – A

D

Clearance

2.6 – 5.6 

(0.102 – 0.220)

—

E

Surface height

−

2.0 – 1.0 

(

−

0.079 – 0.039)

—

Hood – Front fender

B – B

F

Clearance

2.5 – 4.5 

(0.098 – 0.177)

2.0 (0.079)

G

Surface height

−

2.0 – 1.0

 (

−

0.079 – 0.039)

—

C – C

H

Clearance

2.5 – 4.5 

(0.098 – 0.177)

2.0 (0.079)

I

Surface height

−

1.0 – 1.0

 (

−

0.039 – 0.039)

—

Striker – hood 
bumper rubber

—

J

Clearance

32.5 – 33.5 

(1.280 – 1.319)

—