Infiniti G35 (V35) Sedan. Manual - part 381

 

  Index      Infiniti     Infiniti G35 (V35) Sedan - service repair manual 2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  379  380  381  382   ..

 

 

Infiniti G35 (V35) Sedan. Manual - part 381

 

 

PRECAUTIONS

DLK-185

< PRECAUTION >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000000961254

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000000961255

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.

Precaution Necessary for Steering Wheel Rotation after Battery Disconnect

INFOID:0000000000961256

NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-

tion, then disconnect both battery cables.

• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both

battery cables.

• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.

If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.

This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.

OPERATION PROCEDURE

1.

Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.

2.

Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)

PIIB3706J

DLK-186

< PRECAUTION >

[INTELLIGENT KEY SYSTEM]

PRECAUTIONS

3.

Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.

4.

Perform the necessary repair operation.

5.

When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)

6.

Perform self-diagnosis check of all control units using CONSULT-III.

Work

INFOID:0000000000961257

• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their

operational.

• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.

PREPARATION

DLK-187

< PREPARATION >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000000961258

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tools

INFOID:0000000000961259

Tool number
(Kent-Moore No.)
Tool name

Description

(J-39570)
Chassis ear

Locating the noise

(J-43980)
NISSAN Squeak and Rat-
tle Kit

Repairing the cause of noise

SIIA0993E

SIIA0994E

Tool name

Description

Engine ear

Locating the noise

Power tool

SIIA0995E

PIIB1407E

DLK-188

< ON-VEHICLE MAINTENANCE >

[INTELLIGENT KEY SYSTEM]

PRE-INSPECTION FOR DIAGNOSTIC

ON-VEHICLE MAINTENANCE

PRE-INSPECTION FOR DIAGNOSTIC

Basic Inspection

INFOID:0000000000961260

BASIC INSPECTION

1.

CHECK FUNCTION OF INTELLIGENT KEY SYSTEM

Check all Intelligent Key system operation.

If any of Intelligent Key system does not operate>>Refer to 

DLK-167, "Symptom Table"

.

If specific function of Intelligent Key system does not operate>>GO TO 2.

2.

CHECK POWER DOOR LOCK OPERATION

Check door lock/unlock operation by operating door lock and unlock switch.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Refer to 

DLK-168, "DOOR LOCK AND UNLOCK SWITCH : Symptom Table"

.

3.

CHECK DOOR REQUEST SWITCH OPERATION

Check door lock/unlock operation by operating door request switch.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Refer to 

DLK-168, "DOOR REQUEST SWITCH : Symptom Table"

.

4.

CHECK TRUNK OPEN OPERATION

Check trunk open operation by the operating trunk opener switch.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Refer to 

DLK-171, "TRUNK LID OPENER SWITCH : Symptom Table"

.

5.

CHECK TRUNK OPENER REQUEST SWITCH OPERATION

Check trunk open operation by the operating trunk opener request switch.
Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Refer to 

DLK-171, "TRUNK REQUEST SWITCH : Symptom Table"

.

6.

CHECK REMOTE KEYLESS FUNCTION

Check following operation by operating the Intelligent Key remote control button.
• Door lock/unlock function
• Trunk open function

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Refer to 

DLK-169, "INTELLIGENT KEY : Symptom Table"

 (Door lock/unlock function), 

DLK-171,

"INTELLIGENT KEY : Symptom Table"

 (Trunk open function).

7.

CHECK POWER WINDOW OPERATION

Check power window operation by operating power window main switch.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Refer to 

PWC-107, "Diagnosis Procedure"

.

8.

CHECK POWER WINDOW DOWN FUNCTION

Check power window down function by operating Intelligent Key remote control button.
Is the inspection result normal?

 

 

 

 

 

 

 

Content   ..  379  380  381  382   ..