Infiniti G35 (V35) Sedan. Manual - part 16

 

  Index      Infiniti     Infiniti G35 (V35) Sedan - service repair manual 2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  14  15  16  17   ..

 

 

Infiniti G35 (V35) Sedan. Manual - part 16

 

 

ADP-58

< COMPONENT DIAGNOSIS >

B2119 TELESCOPIC SENSOR

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK TELESCOPIC SENSOR POWER SUPPLY

1.

Connect automatic drive positioner control unit connector.

2.

Turn ignition switch ON.

3.

Check voltage between tilt & telescopic sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

CHECK TELESCOPIC SENSOR POWER SUPPLY CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
sensor harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

5.

CHECK TELESCOPIC SENSOR GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
sensor harness connector.

Is the inspection result normal?

YES

>> GO TO 6.

Automatic drive positioner

control unit connector

Terminal

Tilt & telescopic sensor

connector

Terminal

Continuity

M51

23

M48

2

Existed

Automatic drive positioner

control unit connector

Terminal

Ground

Continuity 

M51

23

Not existed

Terminals

Voltage (V)

(Approx.)

(+)

(–)

Tilt & telescopic sensor

Terminal

M48

2

Ground

5

Automatic drive positioner

control unit connector

Terminal

Tilt & telescopic sensor

connector

Terminal

Continuity

M52

33

M48

1

Existed

Automatic drive positioner

control unit connector

Terminal

Ground

Continuity 

M52

33

Not existed

Automatic drive positioner

control unit connector

Terminal

Tilt & telescopic sensor

connector

Terminal

Continuity

M52

41

M48

4

Existed

B2119 TELESCOPIC SENSOR

ADP-59

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

NO

>> Repair or replace harness.

6.

CHECK DOOR MIRROR OPERATION

1.

Connect automatic drive positioner control unit connector and tilt & telescopic sensor connector.

2.

Turn ignition switch ON

3.

Check door mirror operation with memory function.

Is the operation normal?

YES

>> Replace tilt & telescopic sensor. (Built in steering column assembly.)

NO

>> Repair or replace harness.

7.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-39, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit.

NO

>> Repair or replace the malfunctioning part.

ADP-60

< COMPONENT DIAGNOSIS >

B2126 DETENT SW

B2126 DETENT SW

Description

INFOID:0000000000960636

• Detention switch is installed on AT device. It is turned OFF when the AT selector lever is in P position.
• The driver seat control unit judges that the AT selector lever is in P position if continuity does not exist in this

circuit.

DTC Logic

INFOID:0000000000960637

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

STEP 1

Drive the vehicle at 7

±

4km/h or more.

>> GO TO 2.

2.

STEP 2

Check “Self diagnostic result” with CONSULT-III.

Is the DTC detected? 

YES

>> Perform diagnosis procedure. Refer to 

ADP-60, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000000960638

1.

CHECK DTC WITH “BCM”

Check “Self diagnostic result” for BCM with CONSULT-lll.
Is the either DTC B2602, B2603, B2604, B2605 or B2606 detected?

YES

>> Check The DTC. Refer to 

SEC-167, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK DETENTION SWITCH SIGNAL

1.

Turn ignition switch ON.

2.

Select “DETENT SW” in “Data Monitor” mode with CONSULT-lll.

3.

Check detention switch signal under the following condition. 

Is the status normal?

YES

>> GO TO 4.

NO

>> GO TO 3.

3.

CHECK DETENTION SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect driver seat control unit and AT device connector.

3.

Check continuity between driver seat control unit harness connector and AT device harness connector.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

P2126

DETENT SW

AT selector lever is in P position and the vehicle 
speed of 7

±

4km/h is detected.

• Harness and connectors

(Detention switch circuit is 
opened/shorted.)

• Detention switch
• Combination meter

(CAN communacation )

Monitor item

Condition

Status

DETENT SW

AT selector lever

P position

OFF

Other than above

ON

B2126 DETENT SW

ADP-61

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

4.

Check continuity between driver seat control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-39, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace driver seat control unit.

NO

>> Repair or replace the malfunctioning part.

Driver seat control unit connec-

tor

Terminal

AT device connector

Terminal

Continuity

B451

21

M137

11

Existed

Driver seat control unit connec-

tor

Terminal

Ground

Continuity 

B451

21

Not existed

 

 

 

 

 

 

 

Content   ..  14  15  16  17   ..