Infiniti G20 (P11). Manual - part 469

 

  Index      Infiniti     Infiniti G20 (P11) - service repair manual 1999-2002 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  467  468  469  470   ..

 

 

Infiniti G20 (P11). Manual - part 469

 

 

5.

If a leak detector detects a leak, verify at least once by blow-
ing compressed air into area of suspected leak, then repeat
check as outlined above.

6.

Do not stop when one leak is found. Continue to check for
additional leaks at all system components.
If no leaks are found, perform steps 7 - 10.

7.

Start engine.

8.

Set the heater A/C control as follows:

1)

A/C switch ON.

2)

Face mode

3)

Recirculation switch ON

4)

Max cold temperature

5)

Fan speed high

9.

Run engine at 1,500 rpm for at least 2 minutes.

10. Turn engine off and perform leak check again following steps

4 through 6 above.

SHA839E

Refrigerant leaks should be checked immediately after
stopping the engine. Begin with the leak detector at the
compressor. The pressure on the high pressure side will
gradually drop after refrigerant circulation stops and pres-
sure on the low pressure side will gradually rise, as shown
in the graph. Some leaks are more easily detected when
pressure is high.

11. Before connecting ACR4 to vehicle, check ACR4 gauges. No

refrigerant pressure should be displayed. If pressure is
displayed, recover refrigerant from equipment lines and then
check refrigerant purity.

12. Confirm refrigerant purity in supply tank using ACR4 and refrig-

erant identifier.

13. Confirm refrigerant purity in vehicle A/C system using ACR4

and refrigerant identifier.

14. Discharge A/C system using approved refrigerant recovery

equipment. Repair the leaking fitting or component as neces-
sary.

15. Evacuate and recharge A/C system and perform the leak test

to confirm no refrigerant leaks.

16. Conduct A/C performance test to ensure system works

properly.

GI

MA

EM

LC

EC

FE

CL

MT

AT

AX

SU

BR

ST

RS

BT

SC

EL

IDX

SERVICE PROCEDURE

MANUAL

Refrigerant Lines (Cont’d)

HA-207

Belt

TENSION ADJUSTMENT

NCHA0169

I

Refer to MA-13, “Checking Drive Belt”.

Idle Air Control Valve (IACV) — Auxiliary Air
Control (AAC) Valve

INSPECTION

NCHA0199

I

Refer to EC-436, “System Description” and HA-135.

RHA042G

Ventilation Air Filter

FUNCTION

NCHA0171

Air inside passenger compartment is kept clean at either recircula-
tion or fresh mode by installing ventilation air filter into cooling unit.

SHA868E

REPLACEMENT TIMING

NCHA0172

Replace ventilation air filter.
Refer to MA-6, “PERIODIC MAINTENANCE”.
Caution label is fixed inside the glove box.

SHA192F

REPLACEMENT PROCEDURE

NCHA0173

I

Remove glove box.

I

Remove instrument reinforcement from instrument panel.

I

Remove ventilation air filter fixed clip.

I

Take out the lower side ventilation air filter from cooling unit.

I

Then slide upper side filter to the bottom position and take off
the ventilation air filter from the cooling unit.

I

Replace with new one and reinstall on cooling unit.

I

Reinstall instrument reinforcement, glove box and undercover.

SERVICE PROCEDURE

MANUAL

Belt

HA-208

Manual

COMPRESSOR

NCHA0174

Model

ZEXEL make DKV-14G

Type

Vane rotary

Displacement

cm

3

(cu in)/rev.

140 (8.54)

Direction of rotation

Clockwise (viewed from drive end)

Drive belt

Poly V

LUBRICANT

NCHA0175

Model

ZEXEL make DKV-14G

Name

Nissan A/C System Oil Type R

Part number

KLH00-PAGR0

Capacity
m



(US fl oz, Imp fl oz)

Total in system

180 (6.1, 6.3)

Compressor (Service part) charging
amount

180 (6.1, 6.3)

REFRIGERANT

NCHA0176

Type

HFC-134a (R-134a)

Capacity

kg (lb)

0.55 - 0.65 (1.21 - 1.43)

ENGINE IDLING SPEED (WHEN A/C IS ON)

NCHA0177

I

Refer to EC-632, “Idle Speed and Ignition Timing”.

BELT TENSION

NCHA0178

I

Refer to MA-13, “Checking Drive Belts”.

GI

MA

EM

LC

EC

FE

CL

MT

AT

AX

SU

BR

ST

RS

BT

SC

EL

IDX

SERVICE DATA AND SPECIFICATIONS (SDS)

MANUAL

Manual

HA-209

NOTES

 

 

 

 

 

 

 

Content   ..  467  468  469  470   ..