Infiniti FX35 / FX45. Manual - part 735

 

  Index      Infiniti     Infiniti FX35 / FX45 (S50) - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  733  734  735  736   ..

 

 

Infiniti FX35 / FX45. Manual - part 735

 

 

GW-24

< SERVICE INFORMATION >

POWER WINDOW SYSTEM

Terminal and Reference Value for Power Window Main Switch

INFOID:0000000001327969

22

OR

Power window serial link 

Input/Output

IGN SW ON or power window 
timer operating.

38

W/L

Ignition switch
(ON or START) 

Input

Ignition switch 
(ON or START position)

Battery voltage

39

L

CAN - H

Input/Output

40

P

CAN - L

Input/Output

42

L/R

Power source (Fuse)

Input

Battery voltage

49

B

Ground (signal)

0

52

B

Ground (power)

0

53

Y/B

Rap signal

Output

IGN SW ON

Battery voltage

Within 45 second after ignition 
switch is turned to OFF

Battery voltage

When driver side or passen-
ger side door is open in power 
window timer is operates

0

54

W

Power window power supply

Output

Battery voltage

55

G

Power source
(Fusible link)

Input

Battery voltage

62

W

Front door switch 
driver side signal

Input

ON (Open)

OFF (Close)

Battery voltage

Ter-

minal

Wire 

color

Item

Signal

Input/Output

Condition

Voltage [V]

(Approx.)

PIIA2344J

Ter-

minal

Wire 

color

Item

Signal

Input/Output

Condition

Voltage [V]

(Approx.)

1

Y

Rear LH power window 
UP signal

Output

When rear LH switch in
power window main switch is
UP at operated.

Battery voltage

2

SB

Limit switch and encoder 
ground

 

0

3

R

Rear LH power window 
DOWN signal

Output

When rear LH switch in 
power window main switch is 
DOWN at operated.

Battery voltage

4

P

Door key cylinder switch 
LOCK signal

Input

Key position
(Neutral 

 Locked)

 0

5

G

Rear RH power window
DOWN signal

Output

When rear RH switch in 
power window main switch is 
DOWN at operated.

 Battery voltage

6

OR

Door key cylinder switch 
UNLOCK signal

Input

Key position
(Neutral 

 Unlocked)

 0

7

LG

Rear RH power window 
UP signal

Output

When rear RH switch in 
power window main switch is
UP at operated.

 Battery voltage

8

L

Front driver side 
power window motor UP signal

Output

When front LH switch in 
power window main switch is 
 UP at operated

 Battery voltage

POWER WINDOW SYSTEM

GW-25

< SERVICE INFORMATION >

C

D

E

F

G

H

J

K

L

M

A

B

GW

N

O

P

Terminal and Reference Value for Front Power Window Switch (Passenger Side)

INFOID:0000000001327970

9

GY

Limit switch signal

Input

Driver side door window is be-
tween fully-open and just be-
fore fully-closed position (ON)

0

Driver side door window is be-
tween just before fully-closed 
position and fully-closed posi-
tion (OFF)

5

10

BR

Rap signal

Input

IGN SW ON

Battery voltage

Within 45 second after ignition 
switch is turned to OFF

Battery voltage

When driver side or passenger 
side door open in power win-
dow timer is operates

0

11

B

Front driver side
power window motor DOWN 
signal

Output

When front LH switch in 
power window main switch is 
DOWN at operated

 Battery voltage

13

PU

Encoder pulse signal

Input

When power window motor 
operates.

14

Y

Power window serial link

Input/Output

IGN SW ON or power window 
timer operating.

15

W

Encoder power supply

Output

When ignition switch ON or 
power window timer operates

10

17

B

Ground

0

19

W

Battery power supply

Input

Battery voltage

Ter-

minal

Wire 

color

Item

Signal

Input/Output

Condition

Voltage [V]

(Approx.)

OCC3383D

PIIA2344J

Ter-

minal

Wire 

color

Item

Signal

Input/Output

Condition

Voltage [V]

(Approx.)

3

SB

Limit switch and encoder 
ground

Input

 0

4

R

Encoder power supply

Output

When ignition switch ON or 
power window timer operates

10

8

L

Front passenger side 
power window motor UP signal

Output

When power window motor is
UP at operated.

 Battery voltage

9

G

Front passenger side
power window motor DOWN 
signal

Output

When power window motor is 
DOWN at operated.

 Battery voltage

10

W

Battery power supply

Input

Battery voltage

11

B

Ground

0

GW-26

< SERVICE INFORMATION >

POWER WINDOW SYSTEM

CONSULT-III Function

INFOID:0000000001327971

ACTIVE TEST

WORK SUPPORT

DATE MONITOR

12

PU

Encoder pulse signal

Input

When power window motor 
operates.

15

GY

Limit switch signal

Input

Passenger side door window 
is between fully-open and just 
before fully-closed position 
(ON)

0

Passenger side door window 
is between just before fully-
closed position and fully-
closed position (OFF)

5

16

Y

Power window serial link

Input/Output

IGN SW ON or power window 
timer operating.

Ter-

minal

Wire 

color

Item

Signal

Input/Output

Condition

Voltage [V]

(Approx.)

OCC3383D

PIIA2344J

BCM diagnostic test item

Check item diagnostic test mode

Content

RETAINED PWR

Work support

Changes setting of each function.

Data monitor

Displays the input data of BCM in real time.

Active test

Gives a drive signal to a load to check the operation.

Test Item

Description

RETAINED PWR

This test is able to supply RAP signal (power) from BCM (body control module) to power window 
system and power sunroof system (if equipped). Those systems can be operated when turning on 
“RETAINED PWR” on CONSULT-III screen even if the ignition switch is turned OFF.
NOTE:
During this test, CONSULT-III can be operated with ignition switch in “OFF” position. “RETAINED 
PWR” should be turned “ON” or “OFF” on CONSULT-III screen when ignition switch is ON. Then 
turn ignition switch OFF to check retained power operation. CONSULT-III might be stuck if “RE-
TAINED PWR” is turned to “ON” or “OFF” on CONSULT-III screen when ignition switch is OFF.

Work item

Description

RETAINED PWR

Rap signal’s power supply period can be changed by mode setting. Selects rap signal’s power sup-
ply period between three steps
• MODE1 (45 sec.) / MODE2 (OFF) / MODE 3 (2 min.).

Work item

Description

IGN ON SW

Indicates (ON / OFF) condition of ignition switch

POWER WINDOW SYSTEM

GW-27

< SERVICE INFORMATION >

C

D

E

F

G

H

J

K

L

M

A

B

GW

N

O

P

Work Flow

INFOID:0000000001327972

1.

Check the symptom and customer's requests.

2.

Understand the outline of system. Refer to 

GW-15, "System Description"

3.

According to the trouble diagnosis chart, repair or replace the cause of the malfunction.
Refer to 

GW-27, "Trouble Diagnosis Symptom Chart"

.

4.

Does power window system operate normally? Yes, GO TO 5, If No, GO TO 3.

5.

INSPECTION END

Trouble Diagnosis Symptom Chart

INFOID:0000000001327973

Make sure other systems using the signal of the following systems operate normally.

DOOR SW–DR

Indicates (ON / OFF) condition of front door switch driver side 

DOOR SW–AS

Indicates (ON / OFF) condition of front door switch passenger side

Symptom

Repair order

Refer to page

None of the power windows can be operated using any switch.

1. Check BCM power supply and ground circuit

GW-28

2. Check power window main switch power 
supply and ground circuit

GW-28

3. Check power window serial link

GW-45

Driver side power window alone does not operated.

1. Check front power window motor (driver side) 
circuit

GW-30

2. Replace power window main switch

Front passenger side power window alone does not operated.

1. Check front power window switch (passenger 
side) power and ground circuit

GW-30

2. Check power window serial link

GW-45

3. Check front power window motor (passenger 
side) circuit

GW-31

4. Replace BCM

BCS-13

Rear LH side power window alone does not operated

Check rear power window motor (LH) circuit

GW-32

Rear RH side power window alone does not operated

Check rear power window motor (RH) circuit

GW-34

Anti-pinch system does not operate normally (driver side)

1. Door window sliding part malfunction
• A foreign material adheres to window glass or 

glass run rubber.

• Glass run rubber wear or deformation.
• Sash is tilted too much, or no enough.

2. Limit switch adjusting

GW-52

3. Check limit switch circuit (driver side)

GW-36

4. Check encoder circuit (driver side)

GW-39

Anti-pinch system does not operate normally (passenger side)

1. Door window sliding part malfunction
• A foreign material adheres to window glass or 

glass run rubber.

• Glass run rubber wear or deformation.
• Sash is tilted too much, or no enough.

2. Limit switch adjusting

GW-52

3. Check limit switch circuit (passenger side)

GW-37

4. Check encoder circuit (passenger side)

GW-40

Power window retained power operation does not operate properly

1. Check the retained power operation mode 
setting.

GW-26

2. Check door switch

GW-42

3. Replace BCM.

BCS-13

Does not operate by key cylinder switch

1. Check door key cylinder switch

GW-43

2. Replace power window main switch

 

 

 

 

 

 

 

Content   ..  733  734  735  736   ..