Infiniti FX35 / FX45. Manual - part 613

 

  Index      Infiniti     Infiniti FX35 / FX45 (S50) - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  611  612  613  614   ..

 

 

Infiniti FX35 / FX45. Manual - part 613

 

 

EI-16

< SERVICE INFORMATION >

FRONT BUMPER

12. Remove nuts of bumper stay, and remove bumper stay. Remove

nuts with power tool.

13. Remove nuts of front bumper guard bar, and remove front

bumper guard bar. Remove nuts with power tool.

14. Remove fog lamps located in bumper fascia. Refer to 

LT-76,

"Removal and Installation"

.

INSTALLATION

Install in the reverse order of removal.
NOTE:
After installation, adjust the clearance.

REMOVAL AND INSTALLATION OF FILLET MOLDING

Removal 

1.

Remove screws of fillet molding.

2.

Remove clips of fillet molding.

3.

Remove fillet molding.

Installation

1.

Clean adhesive portion of front fender with white gasoline.

2.

Strip pattern from the new double adhesive tape and paste on front fender.

3.

Fillet molding assembly hold with front fender.

REMOVAL AND INSTALLATION OF BUMPER CENTER MOLDING

Removal 

1.

Remove front bumper fascia. Refer to 

EI-15, "Removal and Installation"

.

2.

Remove bumper center molding mounting nuts.

3.

Disengage plastic pawls from bumper fascia.

4.

Remove bumper center molding.

Installation

Install in the reverse order of removal.

PIIA4339E

Portion

Clearance

Front bumper – Front grille 

A – A

0.5 – 3.5 mm (0.020 – 0.138 in)

Front bumper – Headlamp

B – B

1.5 – 4.5 mm (0.059 – 0.177 in)

Front bumper – Front fender

C – C

0.0 – 0.5 mm (0.000 – 0.020 in)

PIIA4350E

REAR BUMPER

EI-17

< SERVICE INFORMATION >

C

D

E

F

G

H

J

K

L

M

A

B

EI

N

O

P

REAR BUMPER

Component Parts Location

INFOID:0000000001328061

1.

Bumper side cover A (RH)

2.

Bumper side cover A (LH)

3.

Special bolt

4.

Clip (“S” type)

5.

Bumper stay (RH)

6.

Bumper reinforcement

7.

Nut

8.

Bumper stay (LH)

9.

Nut

PIIA4333E

EI-18

< SERVICE INFORMATION >

REAR BUMPER

Removal and Installation

INFOID:0000000001529396

CAUTION:

Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.

REMOVAL

1.

Remove bumper side cover A (RH/LH).

2.

Remove fillet molding assembly. Only the place connected with
a rear bumper fascia is removed.

3.

Remove luggage finisher mask (RH/LH).
Refer to 

EI-46, "Removal and Installation"

.

4.

Remove bumper fascia special bolts from rear fender (RH/LH).

5.

Remove bumper fascia bolts from rear fender (RH/LH).

6.

Remove lower portion of bumper fascia bolts.

7.

Insert driver rolled with cloth between bumper fascia and “S”
type clips, and remove bumper fascia.

10. Energy absorber

11.

Fillet molding (LH)

12. Bumper closing (LH)

13. Bolt

14. Bolt

15. Clip (C101)

16. Bolt

17. Clip (C205)

18. Bumper fascia assembly

19. Bumper closing (RH)

20. Fillet molding (RH)

PIIA4347E

PIIA4334E

PIIA4335E

REAR BUMPER

EI-19

< SERVICE INFORMATION >

C

D

E

F

G

H

J

K

L

M

A

B

EI

N

O

P

8.

Remove bumper fascia assembly.

CAUTION:

When removing bumper fascia, 2 workers are required so
as to prevent it from dropping.

9.

Remove bumper energy absorber.

10. Remove bumper reinforcement nuts and remove bumper rein-

force assembly. Remove nuts with power tool.

11. Remove bumper nuts and remove bumper stay. Remove nuts

with power tool.

INSTALLATION

Install in the reverse order of removal.
NOTE:
After installation, adjust the clearance.

DISASSEMBLY AND ASSEMBLY OF REAR BUMPER FASCIA

Disassembly 

1.

Remove rear fender cover bolt and remove rear fender.

2.

Remove bracket clips and remove bracket.

PIIA4336E

PIIA4337E

PIIA4960E

PIIA6416E

 

 

 

 

 

 

 

Content   ..  611  612  613  614   ..