Infiniti EX35. Manual - part 503

DLK-226

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

FRONT DOOR

INSTALLATION

Install in the reverse order of removal.

CAUTION:

Check front door open/close operation after installation.

REAR DOOR

DLK-227

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

REAR DOOR

DOOR ASSEMBLY

DOOR ASSEMBLY : Exploded View

INFOID:0000000003556344

REMOVAL

ADJUSTMENT

1.

Rear door panel

2.

Grommet

3.

Door striker

4.

TORX bolt

5.

Seal rubber

6.

Bumper rubber

7.

Door check link

8.

Door hinge (lower)

9.

Door hinge (upper)

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA2050ZZ

DLK-228

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

REAR DOOR

DOOR ASSEMBLY : Removal and Installation

INFOID:0000000003556345

CAUTION:

• Perform work with 2 workers, because of it’s heavy weight.
• When removing and installing rear door assembly, support door with a jack and cloth to protect door

and body.

REMOVAL

1.

Remove mounting bolts of door check link on the vehicle.

2.

Remove rear door harness grommet, and then pull out door harness from the vehicle.

3.

Disconnect rear door harness connector.

4.

Remove door hinge mounting nuts (door side), and then remove rear door assembly.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Check rear door open/close, lock/unlock operation after installation.

1.

Front fender

2.

Front door 

3.

Rear door

4.

Body side outer

5.

Door striker

6.

TORX bolt

7.

Front door hinge

8.

Rear door hinge (upper)

9.

Rear door hinge (lower)

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA2087GB

REAR DOOR

DLK-229

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to 

DLK-229, "DOOR ASSEMBLY : Adjust-

ment"

.

• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.

DOOR ASSEMBLY : Adjustment

INFOID:0000000003556346

Check the clearance and surface height between rear door and each part by visually and touching. 
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.

Unit: mm (in)

1.

Remove center pillar lower garnish. Refer to 

INT-20, "Removal and Installation"

.

2.

Loosen door hinge mounting nuts on door side.

3.

Adjust the surface height of rear door according to the fitting standard dimension.

4.

Temporarily tighten door hinge mounting nuts on door side.

5.

Loosen door hinge mounting nuts and bolts on body side. 

6.

Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.

7.

After adjustment tighten bolts and nuts to the specified torque.

8.

Install center pillar lower garnish. Refer to .

INT-20, "Removal and Installation"

DOOR STRIKER ADJUSTMENT

Adjust door striker so that it becomes parallel with door lock insertion direction.

DOOR STRIKER

DOOR STRIKER : Exploded View

INFOID:0000000003556347

Portion

Clearance

Surface height

Front door – Rear door

B – B

2.6 – 4.6 (0.102 – 0.181)

-1.0 – 1.0 (-0.039 – 0.039)

Rear door – Body side outer

C – C

2.6 – 4.6 (0.102 – 0.181)

-1.0 – 1.0 (-0.039 – 0.039)

JMKIA1800ZZ