Infiniti EX35. Manual - part 501

DLK-218

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

RADIATOR CORE SUPPORT

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Replenish the following parts.
- Refrigerant: Refer to 

HA-26, "Collection and Charge"

.

- Engine coolant: Refer to 

CO-8, "Refilling"

.

- AT fluid: Refer to 

TM-142, "Changing"

.

- Power steering oil: Refer to 

ST-11, "Inspection"

.

• Adjust the following parts.
- ICC sensor integrated unit (with intelligent cruse control model): Refer to 

CCS-104, "Inspection and

Adjustment"

.

- Front combination lamp: Refer to 

EXL-188, "Aiming Adjustment Procedure"

 (XENON TYPE) or 

EXL-

348, "Aiming Adjustment Procedure"

 (HALOGEN TYPE).

- Around view monitor (BOSE AUDIO WITH NAVIGATION): Refer to 

AV-438, "CALIBRATING CAMERA

IMAGE (AROUND VIEW MONITOR) : Special Repair Requirement"

FRONT FENDER

DLK-219

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

FRONT FENDER

Exploded View

INFOID:0000000003556333

Removal and Installation

INFOID:0000000003556334

CAUTION:

Use a shop cloth to protect the body from being damaged during removal and installation.

REMOVAL

1.

Remove the following parts.
• LH  side

Brake master cylinder cover and hood ledge cover (LH): Refer to 

EXT-23, "Removal and Installation"

.

• RH side

Battery cover and hood ledge cover (RH): Refer to 

EXT-23, "Removal and Installation"

.

2.

Remove clips as shown in the figure by arrows, and remove hood seal assembly (side).

1.

Front fender cover

2.

Hood seal assembly (side)

3.

Front fender

: Pawl

JMKIA2048ZZ

1.

Hood seal assembly (side)

2.

Cowl top cover

JMKIA2091ZZ

DLK-220

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

FRONT FENDER

3.

Remove fender protector. Refer to 

EXT-25, "FENDER PROTECTOR : Removal and Installation"

.

4.

Remove front bumper fascia. Refer to 

EXT-13, "Removal and Installation"

.

5.

Remove front combination lamp. Refer to 

EXL-193, "Removal and Installation"

 (XENON TYPE) or 

EXL-

352, "Removal and Installation"

 (HALOGEN TYPE).

6.

Remove front fender cover.

7.

Remove fillet molding. Refer to 

EXT-32, "Removal and Installation"

8.

Remove center mod guard. Refer to 

EXT-29, "Removal and Installation"

.

9.

Remove mounting bolts except bolt of windshield side.

10. Loosen the mounting bolt (windshield glass side), then pull the front fender upward to remove it.

CAUTION:

• The mounting bolt (windshield glass side) can not be removed because there is not enough

apace, between the front fender and the windshield glass.

• A viscous urethane foam is installed on the back surface of front fender. When removing the

front fender, peel of the urethane foam bit at a time, and carefully to remove it.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• After installation, check front fender adjustment. Refer to 

DLK-212, "HOOD ASSEMBLY : Adjust-

ment"

 and 

DLK-223, "DOOR ASSEMBLY : Adjustment"

.

• After installation, apply the touch-up paint (the body color) onto the head of front fender mounting

bolts.

• Adjust the following part.
- Front combination lamp: Refer to 

EXL-188, "Aiming Adjustment Procedure"

 (XENON TYPE) or 

EXL-

348, "Aiming Adjustment Procedure"

 (HALOGEN TYPE).

- Around view monitor (BOSE AUDIO WITH NAVIGATION): Refer to 

AV-438, "CALIBRATING CAMERA

IMAGE (AROUND VIEW MONITOR) : Special Repair Requirement"

FRONT DOOR

DLK-221

< ON-VEHICLE REPAIR >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

FRONT DOOR

DOOR ASSEMBLY

DOOR ASSEMBLY : Exploded View

INFOID:0000000003556335

REMOVAL

ADJUSTMENT

1.

Front door panel

2.

Grommet

3.

Door striker

4.

TORX bolt

5.

Bumper rubber

6.

Door check link

7.

Door hinge (lower)

8.

Door hinge (upper)

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA2049ZZ