Infiniti EX35. Manual - part 352

BRM-10

< REMOVAL AND INSTALLATION >

BODY COMPONENT PARTS

10. Front roof rail brace (RH & LH)

11.

Upper inner front pillar assembly (RH 
& LH)

12. Inner center pillar (RH & LH)

13. Outer sill (RH & LH)

14. Inner rear pillar (RH & LH)

15. Inner rear pillar reinforcement (RH & 

LH)

16. Outer rear wheelhouse (RH & LH)

17. Upper outer rear wheelhouse exten-

sion (RH & LH)

18. Lower outer rear wheelhouse exten-

sion (RH & LH)

19. Inner rear wheelhouse (RH & LH)

20. Lower inner rear pillar (RH & LH)

21. Roof

22. Front roof rail

23. Roof bow No. 1

24. Roof bow No. 2

25. Roof bow No. 3

26. Roof bow No. 4

27. Rear roof rail

28. Rear fender assembly (RH & LH)

29. Tail pillar assembly (RH & LH)

30. Rear fender extension (RH & LH)

31. Fuel filler lid

32. Rear panel assembly

33. Upper rear bumper retainer

34. Front door assembly (RH & LH)

35. Outer front door panel (RH & LH)

36. Rear door assembly (RH & LH)

37. Outer rear door panel (RH & LH)

38. Inner center front bumper reinforce-

ment

39. Inner center rear bumper reinforce-

ment assembly

40. Rear bumper stay (RH & LH)

: Both sided anti-corrosive precoated steel portions

: High strength steel (HSS) portions

: Both sided anti-corrosive steel and HSS portions

* : Aluminum portion

CORROSION PROTECTION

BRM-11

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

BRM

N

O

P

CORROSION PROTECTION

Description

INFOID:0000000003134492

To provide improved corrosion prevention, the following anti-corrosive measures have been implemented in
NISSAN production plants. When repairing or replacing body panels, it is necessary to use the same anti-cor-
rosive measures.

Anti-Corrosive Precoated Steel (Galvannealed Steel)

To improve repairability and corrosion resistance, a new type of anti-
corrosive precoated steel sheet has been adopted replacing conven-
tional zinc-coated steel sheet.
Galvannealed steel is electroplated and heated to form Zinc-iron
alloy, which provides excellent and long term corrosion resistance
with cationic electrodeposition primer.

Nissan Genuine Service Parts are fabricated from galvannealed steel. Therefore, it is recommended that
GENUINE NISSAN PARTS or equivalent be used for panel replacement to maintain the anti-corrosive perfor-
mance built into the vehicle at the factory.

Phosphate Coating Treatment and Cationic Electrodeposition Primer

A phosphate coating treatment and a cationic electrodeposition
primer, which provide excellent corrosion protection, are employed
on all body components.

CAUTION:

Confine paint removal during welding operations to an absolute
minimum.

Nissan Genuine Service Parts are also treated in the same manner. Therefore, it is recommended that GENU-
INE NISSAN PARTS or an equivalent be used for panel replacement to maintain anti-corrosive performance
built into the vehicle at the factory.

Anti-corrosive Wax

INFOID:0000000003736007

To improve corrosion resistance, anti-corrosive wax is applied inside the body sill and inside other closed sec-
tions. Accordingly, when replacing these parts, be sure to apply anti-corrosive wax to the appropriate areas of
the new parts. Select an excellent anti-corrosive wax which will penetrate after application and has a long shelf
life.

DOOR

SIIA2294E

PIIA0095E

BRM-12

< REMOVAL AND INSTALLATION >

CORROSION PROTECTION

Undercoating

INFOID:0000000003134493

The underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chip-
ping. Therefore, when such a panel is replaced or repaired, apply undercoating to that part. Use an undercoat-
ing which is rust preventive, soundproof, vibration-proof, shock-resistant, adhesive, and durable.

Precautions in Undercoating

1.

Do not apply undercoating to any place unless specified (such as the areas above the muffler and three
way catalyst which are subjected to heat).

2.

Do not undercoat the exhaust pipe or other parts which become hot.

3.

Do not undercoat rotating parts.

4.

Apply bitumen wax after applying undercoating.

5.

After putting seal on the vehicle, put undercoating on it.

B.

Nozzle insert hole

 : Anti-corrosive wax coated portions

JSKIA0584GB

CORROSION PROTECTION

BRM-13

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

BRM

N

O

P

: Undercoated portions

: Sealed portions

JSKIA0585ZZ