Infiniti EX35. Manual - part 1461

 

  Index      Infiniti     Infiniti EX35 - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1459  1460  1461  1462   ..

 

 

Infiniti EX35. Manual - part 1461

 

 

TM-232

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

24. Install revolution sensor to transmission case. Tighten revolution

sensor bolt to the specified torque.

CAUTION:

• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front

edge magnetic area.

• Do not place in an area affected by magnetism.

25. As shown in the figure, use the drift to drive rear oil seal into the

rear extension (2WD) or adapter case (AWD) until it is flush.

CAUTION:

• Do not reuse rear oil seal.
• Apply ATF to rear oil seal.

26. Install return spring (1) to parking pawl (2).

27. Install parking pawl (with return spring) and pawl shaft to rear

extension (2WD) or adapter case (AWD).

SCIA2320E

SCIA5477E

SCIA6180J

SCIA3424E

TRANSMISSION ASSEMBLY

TM-233

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

28. Install parking actuator support from rear extension (2WD) or

adapter case (AWD).

29. Install needle bearing (1) to rear extension (2WD) or adapter

case (AWD).

CAUTION:

Check the direction of needle bearing. Refer to 

TM-207,

"Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"

.

30. Install rear extension assembly (2WD) or adapter case assembly (AWD) according to the following proce-

dures. 

a.

2WD

i.

Install seal rings (1) to output shaft.

ii.

Install parking gear (1) to output shaft (2).

SCIA3423E

SCIA6179J

JPDIA0030ZZ

JPDIA0029ZZ

TM-234

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

iii.

Install output shaft in transmission case.

CAUTION:

Be careful not to mistake front for rear because both sides
looks similar. (Thinner end is front side.)

iv.

Install bearing race to output shaft.

v.

Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to 

GI-15, "Recommended Chemical Prod-

ucts and Sealants"

.) to rear extension assembly as shown in the

figure.

CAUTION:

Completely remove all moisture, oil and old sealant, etc.
from the transmission case and rear extension assembly
mounting surfaces.

vi. Install rear extension assembly to transmission case.

CAUTION:

Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.

SCIA5030E

SCIA5245E

A

: Start and finish point shall be in 
the center of two bolts.

B

: 3 – 5 mm (0.12 – 0.20 in)

Sealant 
width (C)

: 1.0 – 2.0 mm (0.04 – 0.08 in)

Sealant 
height (C)

: 0.4 – 1.0 mm (0.016 – 0.04 in)

JPDIA0036ZZ

SCIA5029E

TRANSMISSION ASSEMBLY

TM-235

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

vii. Tighten rear extension assembly bolts to the specified torque. 

b.

AWD

i.

Install seal rings (1) to output shaft.

ii.

Install parking gear (1) to output shaft (2).

iii.

Install output shaft in transmission case.

CAUTION:

Be careful not to mistake front for rear because both sides
looks similar. (Thinner end is front side.)

1

: Self-sealing bolt

A

:  Bolt

JPDIA0026ZZ

JPDIA0030ZZ

JPDIA0029ZZ

SCIA5030E

 

 

 

 

 

 

 

Content   ..  1459  1460  1461  1462   ..