Infiniti EX35. Manual - part 1452

TM-196

< REMOVAL AND INSTALLATION >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

9.

Disconnect heated oxygen sensor 2 harness connectors (A).

10. Remove heated oxygen sensor 2 harness (B) from clips (1).
11. Remove bracket (2) from transmission assembly.

12. Remove three way catalyst (right bank). Refer to 

EX-5,

"Exploded View"

.

13. Remove front propeller shaft. Refer to 

DLN-75, "Exploded

View"

.

14. Remove control rod. Refer to 

TM-161, "Exploded View"

.

15. Remove crankshaft position sensor (POS) from A/T assembly. Refer to 

EM-114, "Exploded View"

.

CAUTION:

• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front edge magnetic area.
• Do not place in an area affected by magnetism.

16. Remove starter motor. Refer to 

STR-15, "Exploded View"

.

17. Remove rear plate cover. Refer to 

EM-44, "Exploded View (AWD)"

.

18. Turn crankshaft, and remove the four tightening bolts for drive

plate and torque converter.

CAUTION:

When turning the crankshaft, turn it clockwise as viewed
from the front of the engine.

19. Support A/T assembly with a transmission jack.

CAUTION:

When setting the transmission jack, be careful not to allow
it to collide against the drain plug.

20. Remove rear engine mounting member with power tool. Refer to

EM-83, "AWD : Exploded View"

.

21. Remove engine mounting insulator (rear). Refer to 

EM-83,

"AWD : Exploded View"

.

22. Remove dynamic damper. Refer to 

EM-83, "AWD : Exploded View"

.

23. Disconnect A/T assembly harness connector and harness clips.

24. Remove air breather hose. Refer to 

TM-186, "AWD : Exploded View"

.

25. Remove A/T fluid charging pipe from A/T assembly.
26. Remove O-ring from A/T fluid charging pipe.

27. Disconnect fluid cooler tube from the A/T assembly. Refer to 

TM-190, "AWD : Exploded View"

.

28. Plug up openings such as the A/T fluid charging pipe hole, etc.
29. Remove bolts fixing A/T assembly to engine assembly with power tool.

30. Remove A/T assembly with transfer assembly from vehicle.

CAUTION:

• Secure torque converter to prevent it from dropping.
• Secure A/T assembly to a transmission jack.

31. Remove transfer assembly from A/T assembly with power tool.

Refer to 

DLN-50, "Exploded View"

.

INSTALLATION

Note the following, and Install in the reverse order of removal.

: Vehicle front

: Bolt

SCIA8269E

JPDIA0044ZZ

SCIA2203E

TRANSMISSION ASSEMBLY

TM-197

< REMOVAL AND INSTALLATION >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

• When installing A/T assembly to the engine assembly, be sure to

check distance (A) to ensure it is within the reference value limit.

• When installing A/T assembly to the engine assembly, attach the

fixing bolts in accordance with the following standard.

• Align the positions of tightening bolts for drive plate with those of

the torque converter, and temporarily tighten the bolts. Then,
tighten the bolts with the specified torque.

CAUTION:

• When turning crankshaft, turn it clockwise as viewed from the

front of the engine.

• When tightening the tightening bolts for the torque converter

after fixing the crankshaft pulley bolts, be sure to confirm the
tightening torque of the crankshaft pulley mounting bolts.
Refer to 

EM-50, "Exploded View"

.

• Rotate crankshaft several turns and check to be sure that A/T

rotates freely without binding after converter is installed to
drive plate.

• Install crankshaft position sensor (POS). Refer to 

EM-114, "Exploded View"

.

AWD : Inspection

INFOID:0000000003130644

INSPECTION AFTER INSTALLATION

Check the following item after completing installation.
• A/T fluid leakage and A/T fluid level. Refer to 

TM-141, "Inspection"

.

• A/T position. Refer to 

TM-153, "AWD : Inspection and Adjustment"

.

B

:  Scale

C

: Straightedge

Distance (A)

: Refer to 

TM-270, "Torque Converter"

JPDIA0042ZZ

A

: View from vehicle front

: Transmission to engine

: Engine to transmission

Bolt symbol

B

C

Number of bolts

8

4

Bolt length
mm (in)

65 (2.56)

35 (1.38)

Tightening torque
N·m (kg-m, ft-lb)

75 (7.7, 55)

46.6 (4.8, 34)

JPDIA0043ZZ

JPDIA0044ZZ

TM-198

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

DISASSEMBLY AND ASSEMBLY

TRANSMISSION ASSEMBLY

Exploded View

INFOID:0000000003130645

JPDIA0556GB

TRANSMISSION ASSEMBLY

TM-199

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

1.

O-ring

2.

Oil pump cover

3.

O-ring

4.

Oil pump housing

5.

Self-sealing bolt

6.

Torque converter

7.

Converter housing

8.

Oil pump housing oil seal

9.

Bearing race

10.

Needle bearing

11.

O-ring

12.

Front carrier assembly

13.

Needle bearing

14.

Snap ring

15.

Front sun gear

16.

3rd one-way clutch

17.

Snap ring

18.

Bearing race

19.

Needle bearing

20.

Seal ring

21.

Input clutch assembly

22.

Needle bearing

23.

Rear internal gear

24.

Brake band

25.

Mid carrier assembly

26.

Needle bearing 

27.

Bearing race

28.

Rear carrier assembly

29.

Needle bearing 

30.

Mid sun gear

31.

Seal ring

32.

Rear sun gear

33.

1st one-way clutch

34.

Snap ring

35.

Needle bearing

36.

High and low reverse clutch hub

37.

Snap ring

38.

Bearing race

39.

Needle bearing

: Apply Genuine RTV silicone sealant or equivalent. Refer to 

GI-15, "Recommended Chemical Products and Sealants"

.

Refer to 

GI-4, "Components"

 for symbols not described on the above.