Infiniti EX35. Manual - part 1368

 

  Index      Infiniti     Infiniti EX35 - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1366  1367  1368  1369   ..

 

 

Infiniti EX35. Manual - part 1368

 

 

SRC-98

< COMPONENT DIAGNOSIS >

B1135 SIDE MODULE LH

B1135 SIDE MODULE LH

Description

INFOID:0000000003595967

DTC B1135 [VB-SHORT] SIDE MODULE LH

For front LH side air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite sen-
sor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).

OPERATION

In the case of a collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns and introduces the chemical reaction of gas generating materials to
generate hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Front LH side air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front LH side air bag module is installed on the side of front seatback with fixed nuts.

DTC Logic

INFOID:0000000003595968

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (WITH CONSULT-III)

1.

CHECK SELF-DIAG RESULT

1.

Turn ignition switch ON.

2.

Check the screen of CONSULT-III.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-98, "Diagnosis Procedure"

.

NO

>> INSPECTION END

DTC CONFIRMATION PROCEDURE (WITHOUT CONSULT-III)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

CHECK AIR BAG WARNING LAMP

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart. Refer to 

SRC-128, "DTC Index"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003595969

WITH CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1135

SIDE MODULE LH 
[VB-SHORT]

Front LH side air bag module circuit is 
shorted to some power supply circuit

• Disconnection of wiring harness and 

short

• Internal breakdown in front LH side 

air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

B1135 SIDE MODULE LH

SRC-99

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

CHECK FRONT SIDE AIR BAG MODULE

1.

Replace front LH side air bag module. Refer to 

SR-10, "Exploded View"

.

2.

Check “Self diagnosis result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-98, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-16, "Exploded View"

.

2.

Check “Self diagnosis result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-98, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

SRC-100

< COMPONENT DIAGNOSIS >

B1136 SIDE MODULE LH

B1136 SIDE MODULE LH

Description

INFOID:0000000003595970

DTC B1136 [GND-SHORT] SIDE MODULE LH

For front LH side air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite sen-
sor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).

OPERATION

In the case of a collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns and introduces the chemical reaction of gas generating materials to
generate hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Front LH side air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front LH side air bag module is installed on the side of front seatback with fixed nuts.

DTC Logic

INFOID:0000000003595971

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (WITH CONSULT-III)

1.

CHECK SELF-DIAG RESULT

1.

Turn ignition switch ON.

2.

Check the screen of CONSULT-III.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-100, "Diagnosis Procedure"

.

NO

>> INSPECTION END

DTC CONFIRMATION PROCEDURE (WITHOUT CONSULT-III)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

CHECK AIR BAG WARNING LAMP

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart. Refer to 

SRC-128, "DTC Index"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003595972

WITH CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1136

SIDE MODULE LH 
[GND-SHORT]

Front LH side air bag module circuit is 
shorted to ground

• Disconnection of wiring harness and 

short

• Internal breakdown in front LH side 

air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

B1136 SIDE MODULE LH

SRC-101

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

CHECK FRONT SIDE AIR BAG MODULE

1.

Replace front LH side air bag module. Refer to 

SR-10, "Exploded View"

.

2.

Check “Self diagnosis result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-100, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-16, "Exploded View"

.

2.

Check “Self diagnosis result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-100, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

 

 

 

 

 

 

 

Content   ..  1366  1367  1368  1369   ..