Infiniti EX35. Manual - part 1367

SRC-94

< COMPONENT DIAGNOSIS >

B1132 SIDE MODULE RH

B1132 SIDE MODULE RH

Description

INFOID:0000000003595961

DTC B1132 [SHORT] SIDE MODULE RH

For front RH side air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite sen-
sor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).

OPERATION

In the case of a collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns and introduces the chemical reaction of gas generating materials to
generate hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front RH side air bag module is installed on the side of front seatback with fixed nuts.

DTC Logic

INFOID:0000000003595962

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (WITH CONSULT-III)

1.

CHECK SELF-DIAG RESULT

1.

Turn ignition switch ON.

2.

Check the screen of CONSULT-III.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-94, "Diagnosis Procedure"

.

NO

>> INSPECTION END

DTC CONFIRMATION PROCEDURE (WITHOUT CONSULT-III)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

CHECK AIR BAG WARNING LAMP

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart. Refer to 

SRC-128, "DTC Index"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003595963

WITH CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1132

SIDE MODULE RH 
[SHORT]

Front RH side air bag module circuit are 
shorted to each other

• Disconnection of wiring harness and 

short

• Internal breakdown in front RH side 

air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

B1132 SIDE MODULE RH

SRC-95

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

CHECK FRONT SIDE AIR BAG MODULE

1.

Replace front RH side air bag module. Refer to 

SR-10, "Exploded View"

.

2.

Check “Self diagnosis result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-94, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-16, "Exploded View"

.

2.

Check “Self diagnosis result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-94, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

SRC-96

< COMPONENT DIAGNOSIS >

B1134 SIDE MODULE LH

B1134 SIDE MODULE LH

Description

INFOID:0000000003595964

DTC B1134 [OPEN] SIDE MODULE LH

For front LH side air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite sen-
sor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).

OPERATION

In the case of a collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns and introduces the chemical reaction of gas generating materials to
generate hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Front LH side air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front LH side air bag module is installed on the side of front seatback with fixed nuts.

DTC Logic

INFOID:0000000003595965

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (WITH CONSULT-III)

1.

CHECK SELF-DIAG RESULT

1.

Turn ignition switch ON.

2.

Check the screen of CONSULT-III.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-96, "Diagnosis Procedure"

.

NO

>> INSPECTION END

DTC CONFIRMATION PROCEDURE (WITHOUT CONSULT-III)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

CHECK AIR BAG WARNING LAMP

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart. Refer to 

SRC-128, "DTC Index"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003595966

WITH CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device. 

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1134

SIDE MODULE LH 
[OPEN]

Front LH side air bag module circuit is 
open

• Disconnection of wiring harness and 

open

• Internal breakdown in front LH side 

air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

B1134 SIDE MODULE LH

SRC-97

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

CHECK FRONT SIDE AIR BAG MODULE

1.

Replace front LH side air bag module. Refer to 

SR-10, "Exploded View"

.

2.

Check “Self diagnosis result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-96, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-16, "Exploded View"

.

2.

Check “Self diagnosis result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-96, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END