Infiniti EX35. Manual - part 1342

CRASH ZONE SENSOR

SR-13

< ON-VEHICLE REPAIR >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

• In the case that a malfunction is detected by the air bag warning lamp, after reparation or replace-

ment of the malfunctioning parts, reset the memory by self-diagnosis or by the CONSULT-III.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

Refer to 

SRC-14, "Diagnosis Description"

.

SR-14

< ON-VEHICLE REPAIR >

SIDE AIR BAG (SATELLITE) SENSOR

SIDE AIR BAG (SATELLITE) SENSOR

Exploded View

INFOID:0000000003131592

Removal and Installation

INFOID:0000000003131593

WARNING:

• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-

utes.

• Do not use air tools or electric tools for servicing.

REMOVAL

1.

Remove the front seat belt. Refer to 

SB-5, "SEAT BELT RETRACTOR : Removal and Installation"

.

2.

Remove the side air bag (satellite) sensor fixing nuts.

3.

Disconnect harness connector and then remove side air bag (satellite) sensor. 

CAUTION:

• Replace the satellite sensor if it has been dropped or sus-

tained an impact.

• Replace the satellite sensor of deployed SRS front side air

bag module and deployed SRS side curtain air bag module. 

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Do not use old fixing nuts after removal; replace with new nuts.

1.

Side air bag (satellite) sensor

A.

Side air bag (satellite) sensor har-
ness connector

: Vehicle front

Refer to 

GI-4, "Components"

 for symbols in the figure

JMHIA0549GB

JMHIA0009ZZ

SIDE AIR BAG (SATELLITE) SENSOR

SR-15

< ON-VEHICLE REPAIR >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

• In the case that a malfunction is detected by the air bag warning lamp, after reparation or replace-

ment of the malfunctioning parts, reset the memory by self-diagnosis or by the CONSULT-III.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

Refer to 

SRC-14, "Diagnosis Description"

.

SR-16

< ON-VEHICLE REPAIR >

DIAGNOSIS SENSOR UNIT

DIAGNOSIS SENSOR UNIT

Exploded View

INFOID:0000000003131594

Removal and Installation

INFOID:0000000003131595

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes.

• Before disconnecting the air bag diagnosis sensor unit harness connectors, be sure to disconnect

the each harness connector of the air bag module and seat belt pre-tensioner to prevent air bag
deployment by static electricity and seat belt pre-tensioner operation.

• Do not use air tools or electric tools for servicing.

REMOVAL

1.

Disconnect each connector of all air bag modules and pre-tensioner seat belts.

2.

Remove the center console assembly. Refer to 

IP-22, "Removal and Installation"

.

3.

Disconnect diagnosis sensor unit harness connector.

4.

Remove the fixing bolts, ground bolt, and then remove diagnosis sensor unit. 

CAUTION:

• Replace the air bag diagnosis sensor unit if it has been

dropped or sustained an impact.

• Replace the air bag diagnosis sensor unit of deployed SRS air

bag and deployed front seat belt pre-tensioner. 

INSTALLATION

Install in the reverse order of removal.

1.

Diagnosis sensor unit

A.

Diagnosis sensor unit harness connector

B.

Ground bolt

Refer to 

GI-4, "Components"

 for symbols in the figure

JMHIA0550GB

JMHIA0009ZZ