Infiniti EX35. Manual - part 1215

 

2008 EX35 – Electrical 
 

 

ELECTRICAL  

 
 

General Specifications - Charging:   CHG – 31 
 

            Starting:     STR – 18 

 

Battery Hydrometer 
Temperature Corrections:  

PG – 4 

 

Battery Charging:   

PG – 5 

 

Fail-Safe:  

 

PCS – 30 

 

Wire Colors:   

 

GI – 11 

 
 
 

BATTERY CONDITION 

 
Battery Sulphation: 
A battery will be completely discharged if it is left unattended for a long time and the specific 
gravity becomes less than 1.100.  This may result in sulphation on the cell plates.  To 
determine if a battery has been sulfated, note its voltage and current when charging.  If low 
current and higher voltages are observed in the initial stages of charging a sulfated battery is 
likely.  A sulfated battery may sometimes be brought back into service by means of a long slow 
charge, 12 hours or more.  
 
 
•  Do not quick charge a fully discharged battery. 

•  After charging, if the specific gravity of any two cells varies more then .050, the battery 

should be replaced. 

 
 
 
 
 

 

 

RAX-1

TRANSMISSION & DRIVELINE

C

E

F

G

H

I

J

K

L

M

SECTION 

RAX

A

B

RAX

N

O

P

CONTENTS

REAR AXLE

SYMPTOM DIAGNOSIS  ...............................

2

NOISE, VIBRATION AND HARSHNESS 
(NVH) TROUBLESHOOTING  .............................

2

NVH Troubleshooting Chart  ......................................

2

PRECAUTION ...............................................

3

PRECAUTIONS ...................................................

3

Precautions for Drive Shaft  .......................................

3

PREPARATION ............................................

4

PREPARATION ...................................................

4

Special Service Tool  .................................................

4

Commercial Service Tool  ..........................................

4

ON-VEHICLE MAINTENANCE .....................

5

REAR WHEEL HUB AND HOUSING  .................

5

Inspection ..................................................................

5

REAR DRIVE SHAFT ..........................................

6

Inspection ..................................................................

6

ON-VEHICLE REPAIR ..................................

7

REAR WHEEL HUB AND HOUSING  ................

7

Exploded View ..........................................................

7

Removal and Installation  ..........................................

7

Inspection .................................................................

8

REAR DRIVE SHAFT .........................................

9

Exploded View ..........................................................

9

Removal and Installation  ..........................................

9

WHEEL SIDE  ..............................................................

9

WHEEL SIDE : Disassembly and Assembly  ...........

10

FINAL DRIVE SIDE ....................................................

11

FINAL DRIVE SIDE : Disassembly and Assembly ....

11

Inspection ................................................................

13

SERVICE DATA AND SPECIFICATIONS 
(SDS) ............................................................

15

SERVICE DATA AND SPECIFICATIONS 
(SDS) .................................................................

15

Wheel Bearing  .........................................................

15

Drive Shaft ...............................................................

15

RAX-2

< SYMPTOM DIAGNOSIS >

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

SYMPTOM DIAGNOSIS

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NVH Troubleshooting Chart

INFOID:0000000003138875

Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.

×

: Applicable

Reference page

—

RAX-13

—

RAX-7

—

NVH in DLN

 section.

NVH in DLN

 section.

NVH in RAX and RSU sections.

Re

fer 

to RE

AR AXL

E in

 th

is ch

art

.

NVH in WT 

section.

NVH in WT 

section.

Refe

r to

 DRIVE 

SHAFT i

n

 thi

s

 cha

rt.

NVH in BR 

section.

NVH in ST section.

Possible cause and SUSPECTED PARTS

Ex

ce

ss

iv

e joi

nt an

gl

e

Jo

in

t sl

id

in

g

 re

si

st

a

n

c

e

Im

ba

la

nc

e

Imp

rop

er i

ns

ta

lla

ti

o

n,

 lo

os

en

es

s

Part

s interf

erence

PROPELLER S

H

AFT

DIFF

ERENTIAL

REAR A

X

LE 

AND REAR SUSPE

NSION

REAR A

XLE

TI

RE

ROAD WHEE

L

DRIVE SHAFT

BRAKE

STE

E

RING

Symptom

DRIVE 
SHAFT

Noise

×

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

×

REAR AXLE

Noise

×

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

×

Vibration

×

×

×

×

×

×

×

Shimmy

×

×

×

×

×

×

×

Judder

×

×

×

×

×

×

Poor quality ride or handling

×

×

×

×

×

PRECAUTIONS

RAX-3

< PRECAUTION >

C

E

F

G

H

I

J

K

L

M

A

B

RAX

N

O

P

PRECAUTION

PRECAUTIONS

Precautions for Drive Shaft

INFOID:0000000003756668

CAUTION:

Note the following precautions when disassembling and assembling drive shaft.
• Joint sub-assembly does not disassemble because it is non-overhaul parts.
• Perform work in a dust-free location.
• Before disassembling and assembling, clean the parts.
• Prevent the entry of foreign objects during disassembly of the service location.
• Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a

clean cover must be placed over parts.

• Paper waste must be used. Fabric shop cloths must not be used because of the danger of lint adher-

ing to parts.

• Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be

removed by blowing with air or wiping with paper waste.