Infiniti EX35. Manual - part 32

ADP-122

< COMPONENT DIAGNOSIS >

DOOR MIRROR MOTOR

NO

>> Replace door mirror. Refer to 

MIR-52, "DOOR MIRROR ASSEMBLY : Removal and Installation"

.

SEAT MEMORY INDICATOR

ADP-123

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

SEAT MEMORY INDICATOR

Description

INFOID:0000000003134771

• Memory switch is equipped on the seat memory switch installed to the driver side door trim. The operation

signal is inputted to the automatic drive positioner control unit when the memory switch is operated.

• The status of automatic drive positioner system can be checked according to the illuminating/flashing status.

Component Function Check

INFOID:0000000003134772

1.

CHECK FUNCTION

1.

Turn ignition switch ON.

2.

Select “MEMORY SW INDCTR” in “Active test” mode with CONSULT-III. 

3.

Check the memory indicator operation.

Is the operation of relevant parts normal?

YES

>> INSPECTION END

NO

>> Perform diagnosis procedure. Refer to 

ADP-123, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000003134773

1.

CHECK MEMORY INDICATOR POWER SUPPLY

Check voltage between seat memory switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>>

Check the following.

• 10A fuse [No.10 located in fuse block (J/B)].
• Harness for open or short between memory indicator and fuse.

2.

CHECK MEMORY INDICATOR CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit and seat memory switch connector.

3.

Check continuity between automatic drive positioner control unit harness connector and seat memory
switch harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Test item

Description

MEMORY SW INDCTR

OFF

Memory switch indicator

OFF

ON-1

Indicator 1: ON

ON-2

Indicator 2: ON

(+)

(–)

Voltage (V) 

(Approx.)

Seat memory switch

Connector

Terminal

D5

5

Ground

Battery voltage

Automatic drive positioner control unit

Seat memory switch

Continuity

Connector

Terminal

Connector

Terminal

M51

12

D5

6

Existed

13

7

Automatic drive positioner control unit

Ground

Continuity 

Connector

Terminal

M51

12

Not existed

13

ADP-124

< COMPONENT DIAGNOSIS >

SEAT MEMORY INDICATOR

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connector.

3.

CHECK MEMORY INDICATOR

Refer to 

ADP-124, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace seat memory switch. Refer to 

ADP-211, "Removal and Installation"

.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-38, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000003134774

1.

CHECK SEAT MEMORY INDICATOR

1.

Turn ignition switch OFF.

2.

Disconnect seat memory switch connector.

3.

Check continuity between seat memory switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace seat memory switch. Refer to 

ADP-211, "Removal and Installation"

.

Seat memory switch

Continuity

Terminal

(+)

(-)

5

6

Existed

7

DRIVER SEAT CONTROL UNIT

ADP-125

< ECU DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

ECU DIAGNOSIS

DRIVER SEAT CONTROL UNIT

Reference Value

INFOID:0000000003134775

VALUES ON THE DIAGNOSIS TOOL

CONSULT-III MONITOR ITEM

Monitor Item

Condition

Value/Status

SET SW

Set switch

Push

ON

Release

OFF

MEMORY SW1

Memory switch 1

Push

ON

Release

OFF

MEMORY SW2

Memory switch 2

Push

ON

Release

OFF

SLIDE SW–FR

Sliding switch (front)

Operate

ON

Release

OFF

SLIDE SW–RR

Sliding switch (rear)

Operate

ON

Release

OFF

RECLN SW–FR

Reclining switch (front)

Operate

ON

Release

OFF

RECLN SW–RR

Reclining switch (rear)

Operate

ON

Release

OFF

LIFT FR SW–UP

Lifting switch front (up)

Operate

ON

Release

OFF

LIFT FR SW–DN

Lifting switch front (down)

Operate

ON

Release

OFF

LIFT RR SW–UP

Lifting switch rear (up)

Operate

ON

Release

OFF

LIFT RR SW–DN

Lifting switch rear (down)

Operate

ON

Release

OFF

MIR CON SW–UP

Mirror switch

Up

ON

Other than above

OFF

MIR CON SW–DN

Mirror switch

Down

ON

Other than above

OFF

MIR CON SW–RH

Mirror switch

Right

ON

Other than above

OFF

MIR CON SW–LH

Mirror switch

Left

ON

Other than above

OFF

MIR CHNG SW–R

Changeover switch

Right

ON

Other than above

OFF

MIR CHNG SW–L

Changeover switch

Left

ON

Other than above

OFF

TILT SW-UP

Tilt switch

Up

ON

Other than above

OFF

TILT SW-DOWN

Tilt switch

Down

ON

Other than above

OFF