Hyundai Atos: Body Repair Manual - part 33

138

SECTION D-D'

SECTION A-A'

SECTION C-C'

CORROSION PROTECTION - Antivibration pads

ANT-0010

EC ONLY

Center floor panel

SECTION B-B'

Side sill inner panel

10mm

84156-02000

Center floor panel

84156-02000

Rear floor panel

ANT-0011

ANT-0012

ANT-0013

ANT-0014

A

A'

!

!

!

!

B

B'

D'

Rear floor panel

25mm

84158-05000

ANTIVIBRATION PADS-LOCATION & SECTION

D

84152-02000

C'

C

!

!

!

!

84156-02000

84166-02000

84158-05060

84151-02000

84153-02000

84155-02000

84165-02000

84161-02000

84158-05060

84152-02000

139

CORROSION PROTECTION - Attachment of antivibration pads

ANT-0010

ATTACHMENT OF ANTIVIBRATION PADS

Antivibration pads are attached to the upper surface of the floor and at the interior side of the dash panel in order to absorb
vibrations and shut out exhaust gas heat. If these antivibration pads are peeled off in the course of replacement or repair
of a welded panel, cut and attach replacement material (in the shape shown in the figure).

1.

Heat the "antivibration pad" with a heater to soften it.

2.

Align the antivibration pad layer in the position where it is to be
installed, and then press it down with a roller or a block of wood
so that it adheres well.

NOTE
An infrared lamp can also be used to heat both the
antivibration pad layer and the body panels(be sure to
wear gloves).

COR-0006

COR-0007

84152-02000

84156-02000

84166-02000

84158-05060

84151-02000

84153-02000

84155-02000

84165-02000

84161-02000

84158-05060

140

SECTION D-D'

SECTION A-A'

SECTION C-C'

CORROSION PROTECTION - Under  body coat

COR-0040

Dash panel

Center floor panel

Front side rear lower
member

SECTION B-B'

Side outer panel

Side sill inner panel

Center floor panel

Center floor side member

Center floor panel

Rear floor front
extension

Center floor side member

Because parts are to be mounted in these locations, mask the location, before applying
the under body coat.
Under body  coating (Thickness:          : 0.8mm,

: 1.0mm,

 : 2.0mm)

COR-0041

COR-0042

COR-0043

COR-0044

!

!

!

!

B

B'

D'

!

Rear floor panel

Back panel

Fuel tank mounting
rear bracket

Rear floor center
cross member

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

"

UNDER BODY COAT

In order to provide corrosion, stone chipping and vibration resistance, under body coat is applied to the under sides of the
floor  and wheel house.
Therefore, when such  panel is replaced or repaired, apply under body coat to that part.

FLOOR

D

!

"

"

"

"

"

Front side rear
upper member

A

A'

C'

C

!

!

2- Ø  40 Masking

6- Ø  20 Masking

2- Ø  70 Masking

Ø  20 Masking

"

"

"

"

"

"

"

"

"

"

141

SECTION A-A'

CORROSION PROTECTION - Under  body coat

SECTION B-B'

Front apron panel

Front inner lower
pillar

Front side inner
member

Because parts are to be mounted in these locations, mask the location before applying
the under body coat.
Under body  coating (Thickness :

: 1.0mm,

: 2.0mm)

COR-0050/COR-0053/

COR0054

COR-0051

COR-0052

A

A'

!

B'

Wheel house inner
panel (LH)

Fuel filler house

Wheel house inner
panel (RH)

Quarter inner panel (RH)

"

"

"

"

"

SIDE BODY

Ø  20 Masking
(LH ONLY)

Ø  20 Masking

!

!

!

B

!

!

"A"

"B"

Ø  45 Masking

VIEW "A"

VIEW "B"

Ø  45 Masking

Quarter inner
panel (LH)

Front shock cover panel

80Masking