Dodge Neon / Neon SRT-4. Manual - part 658

 

  Index      Dodge     Dodge Neon / Neon SRT-4 - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  656  657  658  659   ..

 

 

Dodge Neon / Neon SRT-4. Manual - part 658

 

 

TEST

ACTION

APPLICABILITY

3

Turn the ignition off to the lock position.
Disconnect the PCM harness connector.
Disconnect the AutoStick/OD Switch harness connector.
NOTE: Check connectors - Clean/repair as necessary.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the AutoStick/OD Off MUX Input circuit between the
AutoStick/OD Switch harness connector and the PCM harness connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 4

No

→ Repair the AutoStick/OD Off MUX Input circuit for an open.

Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

4

Turn the ignition off to the lock position.
Disconnect the PCM harness connector.
Disconnect the AutoStick/OD Switch harness connector.
NOTE: Check connectors - Clean/repair as necessary.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the ground circuit between the AutoStick/OD Switch
harness connector and ground.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 5

No

→ Repair the AutoStick Switch Ground circuit for an open.

Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

5

Turn the ignition off to the lock position.
Disconnect the PCM harness connector.
Disconnect the Autostick/OD switch harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the voltage of the AutoStick/OD Off MUX Input circuit.
Is the voltage above 0.5 volts?

All

Yes

→ Repair the AutoStick/OD Off MUX Input circuit for a short to

voltage.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

No

→ Go To 6

146

TRANSMISSION - NGC

P0953-AUTOSTICK INPUT CIRCUIT HIGH —

Continued

TEST

ACTION

APPLICABILITY

6

Turn the ignition off to the lock position.
Replace the AutoStick Switch per the Service Information.
Ignition on, engine not running.
With the DRBIII

t, erase Transmission DTCs.

In AutoStick mode, perform multiple AutoStick upshifts and downshifts.
With the DRBIII

t, read Transmission DTCs.

Does the DTC return?

All

Yes

→ Go To 7

No

→ Test Complete.

Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

7

Using the schematics as a guide, inspect the wiring and connectors. Repair as
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Powertrain Control Module per the Service Informa-
tion. WITH THE DRBIII

t PERFORM QUICK LEARN AND

REPROGRAM PINION FACTOR.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

8

The conditions necessary to set the DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring and connectors while checking for shorted and open circuits.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair as necessary.

Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

No

→ Test Complete.

147

TRANSMISSION - NGC

P0953-AUTOSTICK INPUT CIRCUIT HIGH —

Continued

Symptom:

P0992-2-4/OD HYDRAULIC PRESSURE TEST FAILURE

When Monitored and Set Condition:

P0992-2-4/OD HYDRAULIC PRESSURE TEST FAILURE

When Monitored:

In any forward gear with engine speed above 1000 RPM shortly after

a shift and every minute thereafter.

Set Condition:

After a shift into a forward gear, with engine speed >1000 RPM, the PCM

momentarily turns on element pressure to the clutch circuits that don’t have pressure to
identify the correct pressure switch closes. If the pressure switch does not close 2 times, the
DTC sets.

POSSIBLE CAUSES

CONDITION P0992 PRESENT

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read Engine DTC’s. Check and repair all Engine DTC’s prior to

performing any transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Powertrain Control Module. Some problems are
corrected by software upgrades to the Transmission and Engine software.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

148

TRANSMISSION - NGC

TEST

ACTION

APPLICABILITY

2

NOTE: The vehicle must be driven to set this DTC. The transmission must be
warm or hot with the Engine RPM above 1000 RPM.
This DTC is an indication of both the 2/4 and the O/D Hydraulic Pressure Switch
DTCs present.
Perform diagnostics for both P0870 and P0845 to determine which switch is the cause
of the DTC.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
If there are no possible causes remaining, view repair.

All

Repair

Refer to the Transmission category and perform the symptoms for
P0845 and P0870.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

149

TRANSMISSION - NGC

P0992-2-4/OD HYDRAULIC PRESSURE TEST FAILURE —

Continued

 

 

 

 

 

 

 

Content   ..  656  657  658  659   ..