Dodge Neon / Neon SRT-4. Manual - part 643

 

  Index      Dodge     Dodge Neon / Neon SRT-4 - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  641  642  643  644   ..

 

 

Dodge Neon / Neon SRT-4. Manual - part 643

 

 

Symptom:

P0740-TCC OUT OF RANGE

When Monitored and Set Condition:

P0740-TCC OUT OF RANGE

When Monitored:

The Torque Converter Clutch (TCC) is in FEMCC or PEMCC, Trans-

mission temperature is hot, Engine temperature is greater than 38° C or 100° F,
Transmission Input Speed greater than 1750 RPM, TPS less than 30°.

Set Condition:

The TCC is modulated by controlling the duty cycle of the L/R Solenoid

until the difference between the Engine and the Transmission Input Speed RPM or duty
cycle is within a desired range. The DTC is set after the period of 10 seconds and 3
occurrences of either: FEMCC - with slip greater than 100 RPM or PEMCC - duty cycle
greater than 85%.

POSSIBLE CAUSES

RELATED DTC’S PRESENT

INTERNAL TRANSMISSION

INTERMITTENT WIRING AND CONNECTORS

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read Engine DTC’s. Check and repair all Engine DTC’s prior to

performing any transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Powertrain Control Module. Some problems are
corrected by software upgrades to the Transmission and Engine software.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

86

TRANSMISSION - NGC

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, read Transmission DTC’s

Are the DTC’s P0750 and/or P0841 present also?

All

Yes

→ Refer to the Transmission category and perform the appropriate

symptom.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

No

→ Go To 3

3

Ignition on, engine not running.
With the DRBIII

t, record and erase DTC’s.

Drive the vehicle until it is fully warmed up. At least 110 degrees.
Perform the following step 3 times.
Drive the vehicle at 50 MPH and allow 4th gear to engage for at least 10 seconds.
Close the throttle, then tip back in until the throttle angle is between 25 and 29
degrees. Note that if you go over 30 degrees, you must back off of the throttle and
retry.
Did the TCC engage during any of the attempts?

All

Yes

→ Go To 4

No

→ Go To 5

4

The conditions necessary to set the DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring and connectors while checking for shorted and open circuits.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair as necessary.

Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

No

→ Test Complete.

5

If there are no possible causes remaining, view repair.

All

Repair

Perform the Hydraulic Pressure test per the Service Information
and repair the internal transmission components and Torque
converter as necessary.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

87

TRANSMISSION - NGC

P0740-TCC OUT OF RANGE —

Continued

Symptom:

P0750-LR SOLENOID CIRCUIT

When Monitored and Set Condition:

P0750-LR SOLENOID CIRCUIT

When Monitored:

Initially at power-up, then every 10 seconds thereafter. The solenoids

will also be tested immediately after a gear ratio or pressure switch error is detected.

Set Condition:

Three consecutive solenoid continuity test failures, or one failure if test is

run in response to a gear ratio or pressure switch error.

POSSIBLE CAUSES

RELATED RELAY DTC’S PRESENT

TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN

LR SOLENOID CONTROL CIRCUIT OPEN

LR SOLENOID CONTROL CIRCUIT SHORT TO GROUND

LR SOLENOID CONTROL CIRCUIT SHORT TO VOLTAGE

LR SOLENOID/PRESSURE SWITCH ASSEMBLY

POWERTRAIN CONTROL MODULE

INTERMITTENT WIRING AND CONNECTORS

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read Engine DTC’s. Check and repair all Engine DTC’s prior to

performing any transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Powertrain Control Module. Some problems are
corrected by software upgrades to the Transmission and Engine software.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

88

TRANSMISSION - NGC

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, read Transmission DTC’s

Are there any Transmission Control Relay DTC’s present also?

All

Yes

→ Refer to the Transmission category and perform the appropriate

symptom.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

No

→ Go To 3

3

With the DRBIII

t, Check the STARTS SINCE SET counter.

NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter for P0750 set at 0?

All

Yes

→ Go To 4

No

→ Go To 11

4

Turn the ignition off to the lock position.
Remove the Starter Relay.
CAUTION: Removal of the Starter Relay is to prevent a Transmission, NO
RESPONSE, condition and disable the starter.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
With the DRBIII

t, actuate the L/R Solenoid.

Monitor the L/R Solenoid LED on the Transmission Simulator.
Did the L/R Solenoid LED on the Transmission Simulator blink on and off during
actuation?

All

Yes

→ Go To 5

No

→ Go To 6

5

If there are no possible causes remaining, view repair.

All

Repair

Replace the Transmission Solenoid/Pressure Switch Assembly per
the Service Information.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

6

Turn the ignition off to the lock position.
Disconnect the PCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the LR Solenoid Control circuit from the appropriate
terminal of special tool #8815 to the Solenoid/Pressure Switch Assembly harness
connector.
Is the resistance above 5.0 ohms?

All

Yes

→ Repair the LR Solenoid Control circuit for an open.

Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

No

→ Go To 7

89

TRANSMISSION - NGC

P0750-LR SOLENOID CIRCUIT —

Continued

 

 

 

 

 

 

 

Content   ..  641  642  643  644   ..