Dodge Neon / Neon SRT-4. Manual - part 642

 

  Index      Dodge     Dodge Neon / Neon SRT-4 - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  640  641  642  643   ..

 

 

Dodge Neon / Neon SRT-4. Manual - part 642

 

 

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, read Transmission DTC’s.

If any of these DTC’s are present, perform their respective tests first.
Are there any Loss of Prime, Line Pressure Sensor and/or Speed Sensor DTCs
present?

All

Yes

→ Refer to the Transmission category and perform the appropriate

symptom. If any of these DTC’s are present, they will cause a gear
ratio error. Perform the test for Loss of Prime first if it is present.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

No

→ Go To 3

3

With the DRBIII

t, perform the 4th gear clutch test. Follow the instructions on the

DRBIII

t.

Increase the throttle angle or TPS Degree to 30° for no more than a few seconds.
CAUTION: Do not overheat the transmission.
Did the clutch test pass - Input Speed remain at zero?

All

Yes

→ Go To 4

No

→ Go To 5

4

The conditions to set this DTC are not current at this time.
Check the gearshift linkage adjustment.
Gear ratio DTC’s can be set by problems in the Input and Output Speed Sensor
circuits. If the vehicle passes the clutch test and still sets gear ratio DTC’s, check the
Speed Sensors for proper operation.
Remove the Starter Relay.
CAUTION: Removal of the Starter Relay is to prevent a Transmission, NO
RESPONSE, condition and disable the starter.
Check the Speed Sensor wiring and connectors for good connection, then perform a
wiggle test using the Transmission Simulator, Miller tool #8333 and the Electronic
Transmission Adapter kit 8333-1A.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair as necessary.

Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

No

→ Test Complete.

5

With the DRBIII

t, read Transmission DTC’s.

Are the DTC’s P0870 and/or P0871 present also?

All

Yes

→ Replace the Solenoid/Pressure Switch Assembly per the Service

Information.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

No

→ Go To 6

82

TRANSMISSION - NGC

P0734-GEAR RATIO ERROR IN 4TH —

Continued

TEST

ACTION

APPLICABILITY

6

If there are no possible causes remaining, view repair.

All

Repair

Repair internal transmission per the Service Information. Check
all of the components related to the OD and 2/4 clutches. Inspect
the Oil Pump and repair or replace per the Service Information.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

83

TRANSMISSION - NGC

P0734-GEAR RATIO ERROR IN 4TH —

Continued

Symptom:

P0736-GEAR RATIO ERROR IN REVERSE

When Monitored and Set Condition:

P0736-GEAR RATIO ERROR IN REVERSE

When Monitored:

The Transmission gear ratio is monitored continuously while the

Transmission is in gear.

Set Condition:

If the ratio of the Input RPM to the Output RPM does not match the

current gear ratio.

POSSIBLE CAUSES

RELATED DTC’S PRESENT

INTERNAL TRANSMISSION

INTERMITTENT GEAR RATIO ERRORS

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read Engine DTC’s. Check and repair all Engine DTC’s prior to

performing any transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Powertrain Control Module. Some problems are
corrected by software upgrades to the Transmission and Engine software.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

84

TRANSMISSION - NGC

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, read Transmission DTC’s.

If any of these DTC’s are present, perform their respective tests first.
Are there any Loss of Prime, Line Pressure Sensor and/or Speed Sensor DTCs
present?

All

Yes

→ Refer to the Transmission category and perform the appropriate

symptom. If any of these DTC’s are present, they will cause a gear
ratio error. Perform the test for Loss of Prime first if it is present.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

No

→ Go To 3

3

With the DRBIII

t, perform the Reverse Gear Clutch test. Follow the instructions on

the DRBIII

t.

Increase the throttle angle or TPS Degree to 30° for no more than a few seconds.
CAUTION: Do not overheat the transmission.
Did the clutch test pass - Input Speed remain at zero?

All

Yes

→ Go To 4

No

→ Go To 5

4

The conditions to set this DTC are not current at this time.
Check the gearshift linkage adjustment.
Gear ratio DTC’s can be set by problems in the Input and Output Speed Sensor
circuits. If the vehicle passes the clutch test and still sets gear ratio DTC’s, check the
Speed Sensors for proper operation.
Remove the Starter Relay.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Check the Speed Sensor wiring and connectors for good connection, then perform a
wiggle test using the Transmission Simulator, Miller tool #8333 and Electronic
Transmission Adapter kit, Miller tool #8333-1.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair as necessary.

Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

No

→ Test Complete.

5

If there are no possible causes remaining, view repair.

All

Repair

Repair internal transmission per the Service Information. Check
all of the components related to the Reverse and LR clutches.
Inspect the Oil Pump and repair or replace per the Service
Information.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

85

TRANSMISSION - NGC

P0736-GEAR RATIO ERROR IN REVERSE —

Continued

 

 

 

 

 

 

 

Content   ..  640  641  642  643   ..