DAF CF65, CF75, CF85 Series . Manual - part 1008

©

 200424

5-1

Tandem rear axle 1132T

TECHNICAL DATA

ΧΦ65/75/85 series

8

0

5. TANDEM REAR AXLE 1132T

5.1 GENERAL

Sealant for differential

Sealant for axle shaft

Wheel bearings

Wheel speed sensor ring

Caster

Mating surface and around bolt holes of axle 

body

Loctite 5910

Mating surface of axle shaft flange

Loctite 5910

Wheel bearing play

0.025 - 0.25 mm

Axial end play

maximum 0.2 mm

Caster

5



TECHNICAL DATA

5-2

©

 200424

Tandem rear axle 1132T

0

ΧΦ65/75/85 series

8

5.2 TIGHTENING TORQUES

The tightening torques stated in this section are 

different from the standard tightening torques 

stated in the overview of the standard tightening 

torques. The other threaded connections not 

specified must therefore be tightened to the 

torque stated in the overview of standard 

tightening torques.

When attachment bolts and nuts are replaced, it 

is important that - unless stated otherwise - these 

bolts and nuts are of exactly the same length and 

property class as those removed. 

Differential

(1) Use Loctite 262 to secure

(2) Use Loctite 243 to secure

(3) Use Loctite 572 to secure

5.3 FILLING CAPACITIES

Hub

First axle drive flanges attachment nut

1385 Nm

(1)

Second axle drive flanges attachment nut

1250 Nm

(1)

Differential lock cover attachment bolts

30 Nm

M12 attachment bolts of pinion housing cover

70 Nm

(2)

Attachment bolts differential to axle housing

170 Nm

(3)

Torx plug (level check/filler and drain plug)

85 Nm

Hub
Hub nut (outside nut)

560 Nm

Axle shaft attachment bolts

260 Nm

Torx plug, wheel hub

85 Nm

Differential

Minimum caster

Maximum caster

Filling capacity of 1

st

 axle

approx. 17.0 litres

approx. 25.0 litres

Filling capacity of 2

nd

 axle

approx. 15.0 litres

approx. 17.5 litres

Oil capacity, per hub

0.8 litres

©

 200424

6-1

Tandem rear axle 1355T

TECHNICAL DATA

ΧΦ65/75/85 series

8

0

6. TANDEM REAR AXLE 1355T

6.1 GENERAL

Sealant for differential

Wheel bearings

(1) Measured at the circumference of the hub

Wheel speed sensor ring

Caster

Mating surface of banjo housing

Loctite 5910

Flanges of attachment nuts and bolts, differential 

to axle housing

Loctite 5910

Bearing-house cover, input shaft

Loctite 5910

Wheel bearings pre-load:
frictional force without hub seal

30 - 62 N

(1)

Axial end play

maximum 0.2 mm

Caster

5



TECHNICAL DATA

6-2

©

 200424

Tandem rear axle 1355T

0

ΧΦ65/75/85 series

8

6.2 TIGHTENING TORQUES

The tightening torques stated in this section are 

different from the standard tightening torques 

stated in the overview of the standard tightening 

torques. The other threaded connections not 

specified must therefore be tightened to the 

torque stated in the overview of standard 

tightening torques.

When attachment bolts and nuts are replaced, it 

is important that - unless stated otherwise - these 

bolts and nuts are of exactly the same length and 

property class as those removed. 

Differential

(1) Use Loctite 262 to secure

(2) Use Loctite 243 to secure

Adjusting the differential lock
Selector shaft adjusting screw is 0.1 mm under 

the mating surface of the differential housing at 

full engaging of the claws.

Hub

(1) Use Loctite 243 to secure

6.3 FILLING CAPACITIES

Hub

Drive flange attachment bolt

1385 Nm

(1)

Differential lock cover attachment bolts

30 Nm

Attachment bolts differential to axle housing:
Attachment bolt M12

110 Nm

(2)

Attachment bolt M14 x 1.5

200 Nm

(2)

Attachment bolts of input shaft bearing cover

60 Nm

Torx plug (level check/filler and drain plug)

85 Nm

Hub nut

2125 Nm

(1)

Locking plate attachment bolts

30 Nm

Planet wheel attachment bolts

45 Nm

Hub cap attachment bolts

30 Nm

Torx plug (level check/filler and drain plug)

85 Nm

Differential

Minimum caster

Maximum caster

Filling capacity of 1

st

 axle

approx. 13.0 litres

approx. 18.0 litres

Filling capacity of 2

nd

 axle

approx. 11.5 litres

approx. 13.0 litres

Oil capacity, per hub

2.0 litres