DAF CF65, CF75, CF85 Series . Manual - part 1007

©

 200424

3-1

Single rear axle 1347

TECHNICAL DATA

ΧΦ65/75/85 series

8

0

3. SINGLE REAR AXLE 1347

3.1 GENERAL

Sealant for differential

Sealant for axle shaft

Wheel speed sensor ring

(1) With a lowered trailing axle

Trailing axle lifting height

Mating surface and around bolt holes of axle 

body

Loctite 5910

Mating surface of axle shaft flange

Loctite 5910

Axial end play

maximum 0.25 mm

Driven axle caster
FAG

3,5



FAS (11/7 ratio)

(1)

4



FAS (10/10 ratio)

(1)

3,5



Other

4,5



Leaf-sprung trailing axle lifting height

100 mm min.

Installation of wheel hub unit
Axle journal for installing the wheel hub unit 

treated with

Gleitmo 805

TECHNICAL DATA

3-2

©

 200424

Single rear axle 1347

0

ΧΦ65/75/85 series

8

3.2 TIGHTENING TORQUES

The tightening torques stated in this section are 

different from the standard tightening torques 

stated in the overview of the standard tightening 

torques. The other threaded connections not 

specified must therefore be tightened to the 

torque stated in the overview of standard 

tightening torques.

When attachment bolts and nuts are replaced, it 

is important that - unless stated otherwise - these 

bolts and nuts are of exactly the same length and 

property class as those removed. 

Differential gear

(1) Use Loctite 262 to secure

(2) Apply Loctite 572

Hub

(1) Only fit a new hub nut

3.3 FILLING CAPACITIES

Drive flange attachment nut

1250 Nm

(1)

Differential lock cover attachment bolts

30 Nm

Attachment bolts differential to axle housing

260 Nm

(2)

Torx plug (level check/filler and drain plug)

85 Nm

Hub nut

(1)

1

st

 phase

500 Nm

2

nd

 phase rpm

turn the hub 10 revolutions at a speed of 

approx. 40 rpm

3

rd

 phase

550 Nm

4

th

 phase rpm

turn the hub 10 revolutions at a speed of 

approx. 40 rpm

5

th

 phase

1300 Nm

Axle shaft attachment bolts

260 Nm

Differential

Minimum caster

Maximum caster

Filling capacity

approx. 21.5 litres

approx. 23.5 litres

©

 200424

4-1

Single rear axle 1354

TECHNICAL DATA

ΧΦ65/75/85 series

8

0

4. SINGLE REAR AXLE 1354

4.1 GENERAL

Sealant for differential

Wheel bearings

(1) Measured at the circumference of the hub

Wheel speed sensor ring

(1) With a lowered trailing axle

Trailing axle lifting height

Studs from axle housing

Mating face and around stud bolts of banjo 

housing

Loctite 5910

Wheel bearings pre-load:
frictional force without hub seal

30 - 62 N

(1)

Axial end play

maximum 0.25 mm

Driven axle caster
FAG

3,5



FAS (11/7 ratio)

(1)

4,0



FAS (10/10 ratio)

(1)

3,5



Other

4,5



Leaf-sprung trailing axle lifting height

100 mm min.

Fit studs with locking compound

Loctite 243

TECHNICAL DATA

4-2

©

 200424

Single rear axle 1354

0

ΧΦ65/75/85 series

8

4.2 TIGHTENING TORQUES

The tightening torques stated in this section are 

different from the standard tightening torques 

stated in the overview of the standard tightening 

torques. The other threaded connections not 

specified must therefore be tightened to the 

torque stated in the overview of standard 

tightening torques.

When attachment bolts and nuts are replaced, it 

is important that - unless stated otherwise - these 

bolts and nuts are of exactly the same length and 

property class as those removed. 

Differential

(1) Use Loctite 262 to secure

Hub

(1) Use Loctite 243 to secure

4.3 FILLING CAPACITIES

Differential

Hub

Drive flange attachment nut

1325 Nm

(1)

Locking nut of differential-lock cylinder

80 Nm

Attachment nuts differential to axle housing

260 Nm

Torx plug (level check/filler and drain plug)

85 Nm

Hub nut

2125 Nm

Locking plate attachment bolts

30 Nm

(1)

Planet wheel attachment bolts

45 Nm

Hub cap attachment bolts

30 Nm

Torx plug (level check/filler and drain plug)

85 Nm

Filling capacities

approx. 16.5 litres

Oil capacity, per hub

2.0 litres