Chrysler Town, Dodge Caravan. Manual - part 791

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  789  790  791  792   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 791

 

 

TEST

ACTION

APPLICABILITY

3

Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the Power Liftgate Module C2 harness connector.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
With the DRBIII

t select Pep Module Tools.

Select lab scope.
Select Live Data.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Set Probe to x10.
Press F2 again when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the Power Liftgate Module C2 connector.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?

All

Yes

→ Go To 4

No

→ Repair the PCI Bus circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

4

Turn the ignition off.
Disconnect the Power Liftgate Module C2 harness connector.
Turn the ignition on.
Measure the resistance between ground and the Liftgate Module Wake Up Signal
circuit.
Is the resistance below 50.0 ohms?

All

Yes

→ Go To 5

No

→ Go To 8

5

Turn the ignition off.
Disconnect the Body Control Module C2 harness connector.
Disconnect the Power Liftgate Module C2 harness connector.
Turn the ignition on.
Measure the voltage of the Liftgate Module Wake Up Signal circuit.
Is there any voltage present?

All

Yes

→ Repair the Liftgate Module Wake Up Signal wire for a short to

voltage.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 6

400

COMMUNICATION

*NO RESPONSE FROM POWER LIFTGATE MODULE —

Continued

TEST

ACTION

APPLICABILITY

6

Turn the ignition off.
Disconnect the Body Control Module C2 harness connector.
Disconnect the Power Liftgate Module C2 harness connector.
Measure the resistance between ground and the Liftgate Module Wake Up Signal
circuit.
Is the resistance below 100.0 ohms?

All

Yes

→ Repair the Liftgate Module Wake Up Signal wire for a short to

ground.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 7

7

If there are no possible causes remaining, view repair.

All

Repair

Replace the Power Liftgate Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.

8

Turn the ignition off.
Disconnect the Body Control Module C2 harness connector.
Disconnect the Power Liftgate Module C2 harness connector.
Measure the resistance of the Liftgate Module Wake Up Signal circuit between the
BCM C2 connector and the Power Liftgate Module C2 connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Replace the Body Control Module in accordance with the service

information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Repair the Liftgate Module Wake Up Signal wire for an open.

Perform BODY VERIFICATION TEST - VER 1.

401

COMMUNICATION

*NO RESPONSE FROM POWER LIFTGATE MODULE —

Continued

Symptom:

*NO RESPONSE FROM RADIO

POSSIBLE CAUSES

NO RESPONSE FROM RADIO

OPEN FUSED ACCESSORY RELAY OUTPUT CIRCUIT

OPEN FUSED B+ CIRCUIT

GROUND CIRCUIT OPEN

OPEN PCI BUS CIRCUIT

RADIO

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
Note: As soon as one or more module communicates with the DRB, answer
the question.
With the DRB, attempt to communicate with the Airbag Control Module (ACM).
With the DRB, attempt to communicate with the Body Control Module (BCM).
Was the DRB able to I/D or establish communications with either of the modules?

All

Yes

→ Go To 2

No

→ Refer to the Communications category and perform the symptom

PCI Bus Communication Failure.
Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Disconnect the Radio C1 harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused Accessory Relay
Output circuit.
Is the test light illuminated?

All

Yes

→ Go To 3

No

→ Check fuse #5 in the IPM for an open. If ok, repair the Fused

Accessory Relay Output circuit for an open or short. Refer to the
wiring diagrams located in the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

3

Turn the ignition off.
Disconnect the Radio C1 harness connector.
Using a 12-volt test light connected to ground, probe both Fused B+ circuits.
Is the test light illuminated for each circuit?

All

Yes

→ Go To 4

No

→ Check fuse #14 in the IPM for an open. If ok, repair the Fused B+

circuit for an open or short. Refer to the wiring diagrams located
in the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

402

COMMUNICATION

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the Radio C1 harness connector.
Using a 12-volt test light connected to 12-volts, probe both ground circuits.
Is the test light illuminated for each circuit?

All

Yes

→ Go To 5

No

→ Repair the ground circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

5

Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the Radio C1 harness connector.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
Install DRBIII

t SuperCard 2 CH8361 into DRBIIIt.

With the DRBIII

t select Pep Module Tools.

Select lab scope.
Select Live Data.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Set Probe to x10.
Press F2 again when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the Radio connector.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?

All

Yes

→ Go To 6

No

→ Repair the PCI Bus circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

6

If there are no possible causes remaining, view repair.

All

Repair

Replace the Radio.
Perform BODY VERIFICATION TEST - VER 1.

403

COMMUNICATION

*NO RESPONSE FROM RADIO —

Continued

 

 

 

 

 

 

 

Content   ..  789  790  791  792   ..