Chrysler Town, Dodge Caravan. Manual - part 790

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  788  789  790  791   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 790

 

 

Symptom:

*NO RESPONSE FROM PCM (SCI ONLY) - SBEC

POSSIBLE CAUSES

CHECK PCM POWERS AND GROUNDS

SCI TRANSMIT CIRCUIT SHORTED TO VOLTAGE

TRANSMISSION CONTROL MODULE

SCI RECEIVE CIRCUIT SHORTED TO VOLTAGE

SCI CIRCUITS SHORTED TOGETHER

SCI TRANSMIT CIRCUIT SHORTED TO GROUND

SCI RECEIVE CIRCUIT SHORTED TO GROUND

SCI RECEIVE CIRCUIT OPEN

SCI TRANSMIT CIRCUIT OPEN

POWERTRAIN CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Perform the symptom Checking PCM Power and Ground Circuits in the Driveability
category.
NOTE: With the DRBIII

in the generic scan tool mode, attempt to commu-

nicate with the PCM.
NOTE: If the DRBIII

can communicate with the PCM in the generic scan

tool mode, it may not be necessary to perform this step.
Did the vehicle pass this test?

All

Yes

→ Go To 2

No

→ Repair as necessary.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

2

Turn the ignition off.
Disconnect the PCM C2 harness connector.
Disconnect the DRB from the DLC.
Measure the resistance between ground and the SCI Transmit (PCM) circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 3

No

→ Go To 4

3

Turn the ignition off.
Disconnect the TCM harness connector (if equipped).
NOTE: If vehicle is not equipped with a TCM, answer yes to the question.
Measure the resistance between ground and the SCI Transmit (PCM) circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the SCI Transmit (PCM) circuit for a short to ground.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→ Replace the Transmission Control Module in accordance with the

service information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

396

COMMUNICATION

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the DRB from the DLC.
Disconnect the PCM harness connectors.
Disconnect the TCM harness connector (if equipped).
Turn the ignition on.
Measure the voltage of the SCI Transmit (PCM) circuit at the DLC connector.
Is the voltage above 1.0 volt?

All

Yes

→ Repair the SCI Transmit (PCM) circuit for a short to voltage.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→ Go To 5

5

Turn the ignition off.
Disconnect the DRB from the DLC.
Disconnect the PCM harness connectors.
Turn the ignition on.
Measure the voltage of the SCI Receive (PCM) circuit at the DLC connector.
Is the voltage above 1.0 volt?

All

Yes

→ Repair the SCI Receive (PCM) circuit for a short to voltage.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→ Go To 6

6

Turn the ignition off.
Disconnect the DRB from the DLC.
Disconnect the PCM harness connectors.
Measure the resistance between the SCI Transmit (PCM) circuit and the SCI Receive
(PCM) circuit at the PCM connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the short between the SCI Transmit (PCM) and the SCI

Receive (PCM) circuits.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→ Go To 7

7

Turn the ignition off.
Disconnect the PCM C2 harness connector.
Disconnect the DRB from the DLC.
Measure the resistance between ground and the SCI Receive (PCM) circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the SCI Receive (PCM) circuit for a short to ground.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→ Go To 8

8

Turn the ignition off.
Disconnect the PCM C2 harness connector.
Disconnect the DRB from the DLC.
Measure the resistance of the SCI Receive (PCM) circuit between the PCM C2
connector and the DLC.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 9

No

→ Repair the SCI Receive (PCM) circuit for an open.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

397

COMMUNICATION

*NO RESPONSE FROM PCM (SCI ONLY) - SBEC —

Continued

TEST

ACTION

APPLICABILITY

9

Turn the ignition off.
Disconnect the PCM C2 harness connector.
Disconnect the DRB from the DLC.
Measure the resistance of the SCI Transmit (PCM) circuit between the PCM C2
connector and the DLC.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 10

No

→ Repair the SCI Transmit (PCM) circuit for an open.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

10

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

398

COMMUNICATION

*NO RESPONSE FROM PCM (SCI ONLY) - SBEC —

Continued

Symptom:

*NO RESPONSE FROM POWER LIFTGATE MODULE

POSSIBLE CAUSES

FUSED B(+) CIRCUIT OPEN

GROUND CIRCUIT OPEN

BODY CONTROL MODULE - LIFTGATE WAKE UP GROUND OPEN

LIFTGATE MODULE WAKE UP SIGNAL WIRE OPEN

LIFTGATE MODULE WAKE UP SIGNAL WIRE SHORT TO VOLTAGE

LIFTGATE MODULE WAKE UP SIGNAL WIRE SHORT TO GROUND

PCI BUS CIRCUIT OPEN

POWER LIFTGATE MODULE - OPEN

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Disconnect the Power Liftgate Module C1 harness connector.
Measure the voltage of the Fused B(+) circuit.
Is the voltage above 10.0 volts?

All

Yes

→ Go To 2

No

→ Repair the Fused B(+) circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Disconnect the Power Liftgate Module C1 harness connector.
Using a 12-volt test light connected to 12-volts, check the Ground circuit.
Does the test light illuminate brightly?

All

Yes

→ Go To 3

No

→ Repair the Ground circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

399

COMMUNICATION

 

 

 

 

 

 

 

Content   ..  788  789  790  791   ..