Chrysler Town, Dodge Caravan. Manual - part 634

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  632  633  634  635   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 634

 

 

TEST

ACTION

APPLICABILITY

7

If there are no possible causes remaining, view repair.

All

Repair

Replace the Camshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

8

Turn the ignition off.
Disconnect the CMP Sensor connector.
Disconnect the PCM connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance in the (K44) CMP Signal circuit from the CMP harness
connector to the appropriate terminal of special tool #8815.
Wiggle the related wire harness while taking this measurement.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 9

No

→ Repair the open/high resistance in the (K44) CMP Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

9

Turn the ignition off.
Disconnect the PCM connector.
Disconnect the CMP Sensor connector.
Measure the resistance between ground and the (K44) CMP Signal circuit in the
CMP Sensor harness connector.
Wiggle the related wire harness while monitoring the resistance value.
Does the resistance stay below 100 ohms?

All

Yes

→ Repair the short to ground in the (K44) CMP Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→ Go To 10

10

Turn the ignition off.
Disconnect the CMP Sensor connector.
Ignition on, engine not running.
Measure the voltage on the (K44) CMP Signal circuit.
Wiggle the related wire harness while taking this measurement.
Does the voltage ever increase above 5.5 volts?

All

Yes

→ Repair the short to B+ voltage in the (K44) CMP Signal circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→ Go To 11

11

Turn the ignition off.
Disconnect the PCM harness connector.
Disconnect the CMP harness connector.
Measure the resistance between the (K6) 5 Volt Supply circuit and the signal circuit
in the CMP harness connector.
Wiggle the related wire harness while taking this measurement.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the short to the (K6) 5 Volt Supply circuit in the (K44)

CMP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→ Go To 12

344

DRIVEABILITY - NGC

P0344-CAMSHAFT POSITION SENSOR INTERMITTENT —

Continued

TEST

ACTION

APPLICABILITY

12

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

345

DRIVEABILITY - NGC

P0344-CAMSHAFT POSITION SENSOR INTERMITTENT —

Continued

Symptom List:

P0351-IGNITION COIL #1 CIRCUIT
P0352-IGNITION COIL #2 CIRCUIT

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0351-IGNITION COIL #1 CIR-
CUIT.

When Monitored and Set Condition:

P0351-IGNITION COIL #1 CIRCUIT

When Monitored:

With battery voltage greater than 11 volts. Engine running. Engine

RPM less than 8160. No coil in dwell during test.

Set Condition:

Peak current is not achieved with battery based dwell plus 1.5 msec of

diagnostic offset. It takes less than 3 seconds during cranking or up to 6 seconds while
running to set. One Trip Fault.

P0352-IGNITION COIL #2 CIRCUIT

When Monitored:

With battery voltage greater than 11 volts. Engine running. Engine

RPM less than 8160. No coil in dwell during test.

Set Condition:

Peak current is not achieved with battery based dwell plus 1.5 msec of

diagnostic offset. It takes less than 3 seconds during cranking or up to 6 seconds while
running to set. One trip Fault.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

IGNITION COIL

(A142) ASD RELAY OUTPUT CIRCUIT

IGNITION COIL DRIVER CIRCUIT OPEN

COIL CONTROL CIRCUIT SHORTED TO GROUND

PCM

TEST

ACTION

APPLICABILITY

1

NOTE: Record the Freeze Frame Information that set along with the DTC.
Turn the ignition on.
With the DRBIII

t, read DTC’s.

Is the Good Trip displayed and equal to zero?

All

Yes

→ Go To 2

No

→ Refer to the INTERMITTENT CONDITION symptom in the

Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

346

DRIVEABILITY - NGC

TEST

ACTION

APPLICABILITY

2

Turn the ignition off.
Disconnect the Ignition Coil harness connector.
Turn the ignition on.
With the DRBIII

t, actuate the ASD Relay.

Using a 12-volt test light connected to ground, probe the (A142) ASD Relay Output
circuit in the Ignition Coil harness connector.
Does the test light illuminate brightly?

All

Yes

→ Go To 3

No

→ Repair the (A142) ASD Relay Output circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

3

Turn the ignition off.
Disconnect the Ignition Coil harness connector.
Using a 12-volt test light connected to 12-volts, probe the Ignition Coil Driver circuit.
Crank the engine for 5 second while observing the test light.
Does the test light blink/flicker?

All

Yes

→ Replace the Ignition Coil.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→ Go To 4

4

Turn the ignition off.
Disconnect the Ignition Coil harness connector.
Disconnect the PCM harness connector.
Measure the resistance of the Coil Control circuit between the Ignition Coil harness
connector and the PCM harness connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 5

No

→ Repair the Coil Control circuit for an open.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

5

Turn the ignition off.
Disconnect the Ignition Coil harness connector.
Disconnect the PCM harness connector.
Measure the resistance between ground and the Coil Control circuit in the Ignition
Coil harness connector.
Is the resistance below 100k ohms?

All

Yes

→ Repair the Coil Control circuit for a short to ground.

Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→ Go To 6

6

NOTE: Before continuing, check the PCM harness connector terminals for corrosion,
damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

347

DRIVEABILITY - NGC

P0351-IGNITION COIL #1 CIRCUIT —

Continued

 

 

 

 

 

 

 

Content   ..  632  633  634  635   ..