Chrysler Town, Dodge Caravan. Manual - part 603

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  601  602  603  604   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 603

 

 

Symptom:

*CHECKING THE A/C RELAY OUTPUT

POSSIBLE CAUSES

A/C CLUTCH RELAY OPERATION

GROUND CIRCUIT OPEN

A/C CLUTCH

FUSED B+ CIRCUIT

A/C CLUTCH OUTPUT CIRCUIT

IPM FUSE & RELAY CENTER

A/C CLUTCH RELAY

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure that the refrigerant system is properly charged. Refer to the
appropriate Service Information.
Turn the ignition on.
With the DRBIII

t, actuate the A/C Clutch Relay.

Is the A/C Clutch actuating?

All

Yes

→ The A/C Clutch System operating properly at this time.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

No

→ Go To 2

2

Turn the ignition off.
Disconnect the A/C Clutch harness connector.
Measure the Ground circuit in the A/C Clutch harness connector to ground.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 3

No

→ Repair the open in the Ground circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

3

Disconnect the A/C Clutch harness connector.
Turn the ignition on.
With the DRBIII

t, actuate the A/C Clutch Relay.

Measure the voltage of the (C3) A/C Clutch Relay Output circuit in the A/C Clutch
harness connector.
Is the voltage above 11.0 volts?

All

Yes

→ Replace the A/C Clutch.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

No

→ Go To 4

220

DRIVEABILITY - SBEC

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Remove the A/C Clutch Relay from the IPM.
Using a 12-volt test light connected to ground, probe the Fused B+ circuit in the IPM.
Does the test light illuminate brightly?

All

Yes

→ Go To 5

No

→ Check for an open A/C Clutch fuse, repair the cause of the open

fuse. If OK, replace the IPM Fuse & Relay Center.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

5

Turn the ignition off.
Disconnect the IPM C3 harness connector.
Disconnect the A/C Clutch harness connector.
Measure the resistance of the (C3) A/C Clutch Relay Output circuit between the IPM
harness connector and the A/C Clutch harness connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 6

No

→ Repair the open in the (C3) A/C Clutch Relay Output circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

6

NOTE: Ensure all IPM harness connectors are connected.
Turn the ignition off.
Disconnect the A/C Clutch harness connector.
Remove the A/C Clutch Relay from the IPM.
Measure the resistance of the (C3) A/C Clutch Relay Output circuit between the IPM
and the A/C Clutch harness connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Replace the A/C Clutch Relay.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

No

→ Replace the IPM Fused & Relay Center.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

221

DRIVEABILITY - SBEC

*CHECKING THE A/C RELAY OUTPUT —

Continued

Symptom:

INTERMITTENT CONDITION

POSSIBLE CAUSES

INTERMITTENT CONDITION

TEST

ACTION

APPLICABILITY

1

NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Refer to any Technical Service Bulletins (TSBs) that may apply.
Review the DRB Freeze Frame information. If possible, try to duplicate the
conditions under which the DTC set.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wire harness. Look for parameter
values to change and/or a DTC to set.
Visually inspect the related wire harness. Look for any chafed, pierced, pinched,
partially broken wires and broken, bent, pushed out, or corroded terminals.
CAUTION: NEVER PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Inspect and clean all PCM, engine, and chassis grounds.
If numerous trouble codes were set, use a wire schematic to help you find any
common ground or supply circuits.
For any Relay DTCs, actuate the Relay with the DRBIII

t and wiggle the related wire

harness to try to interrupt the actuation.
For intermittent Evaporative Emission trouble codes perform a visual and physical
inspection of the related parts including hoses and the Fuel cap.
A co-pilot, data recording, and/or lab scope should be used to help diagnose
intermittent conditions.
Use the DRBIII

t to perform a System Test if one applies to failing component.

Were any problems found during the above inspections?

All

Yes

→ Repair as necessary

No

→ Test Complete.

222

DRIVEABILITY - NGC

Symptom:

P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT

When Monitored and Set Condition:

P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT

When Monitored:

Engine cranking and Engine running

Set Condition:

Powertrain Control Module detects an error when the camshaft position is

out of phase with the crankshaft position.

POSSIBLE CAUSES

INTERMITTENT CONDITION

CHECKING INTERMITTENT CMP SIGNAL WITH LAB

CMP WIRE HARNESS INSPECTION

TONE WHEEL/PULSE RING INSPECTION

CKP WIRE HARNESS INSPECTION

TONE WHEEL/PULSE RING INSPECTION

INTERMITTENT CKP SIGNAL

CAMSHAFT POSITION SENSOR

CRANKSHAFT POSITION SENSOR

TEST

ACTION

APPLICABILITY

1

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
With the DRBIII

t, read DTCs and record the related Freeze Frame data.

With the DRBIII

t, erase DTCs.

Start the engine and run until operating temp is reached. (Closed Loop)
If the DTC does not reset it may be necessary to take the vehicle on a test drive.
Does the DTC reset?

All

Yes

→ Go To 2

No

→ Refer to the INTERMITTENT CONDITION symptom in the

Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

223

DRIVEABILITY - NGC

 

 

 

 

 

 

 

Content   ..  601  602  603  604   ..