Chrysler Town, Dodge Caravan. Manual - part 1150

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1148  1149  1150  1151   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 1150

 

 

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Fuel Pressure Sensor harness connector.
Disconnect the ECM harness connectors.
Remove the ECM/PCM Relay from the IPM.
Connect a jumper wire between cavity 30 and cavity 87 of the ECM/PCM Relay
connector.
Turn the ignition on.
Measure the voltage on the Fuel Pressure Sensor 5-Volt Supply circuit.
Is the voltage below 1.0 volt?

All

Yes

→ Go To 4

No

→ Repair the Fuel Pressure Sensor 5-Volt Supply circuit for a short

to voltage.
Perform ROAD TEST VERIFICATION - VER-2.

NOTE: Remove the jumper wire and reinstall the ECM/PCM Relay.

4

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

5

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

→ Repair as necessary.

Perform ROAD TEST VERIFICATION - VER-2.

No

→ Test Complete.

143

DRIVEABILITY - DIESEL

P0641-SENSOR REFERENCE VOLTAGE A CKT VOLTAGE TOO HIGH —

Continued

Symptom:

P0641-SENSOR REFERENCE VOLTAGE A CKT VOLTAGE TOO LOW

When Monitored and Set Condition:

P0641-SENSOR REFERENCE VOLTAGE A CKT VOLTAGE TOO LOW

When Monitored:

With the ignition on.

Set Condition:

The ECM detects a short to ground on the Sensor Reference Voltage A

circuit or the Fuel Pressure Sensor 5-Volt Supply circuit.

POSSIBLE CAUSES

INTERMITTENT CONDITION

FUEL PRESSURE SENSOR SHORTED TO GROUND

MASS AIR FLOW SENSOR SHORTED TO GROUND

ENGINE OIL PRESSURE SENSOR SHORTED TO GROUND

SENSOR REFERENCE VOLTAGE A CIRCUIT SHORTED TO GROUND

SENSOR REFERENCE VOLTAGE A CIRCUIT SHORTED TO SENSOR GROUND

FUEL PRESSURE SENSOR 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND

FUEL PRESSURE SENSOR 5-VOLT SUPPLY CIRCUIT SHORTED TO SENSOR GROUND

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
Turn the ignition on.
With the DRB, erase ECM DTCs.
Turn the ignition off for 10 seconds.
Turn the ignition on.
Monitor the DRB for ECM DTCs.
Did this DTC set again?

All

Yes

→ Go To 2

No

→ Go To 10

2

Turn the ignition off.
Disconnect the Fuel Pressure Sensor harness connector.
Turn the ignition on.
Measure the voltage of the Fuel Pressure Sensor 5-Volt Supply circuit.
Is the voltage above 4.8 volts?

All

Yes

→ Replace the Fuel Pressure Sensor.

Perform ROAD TEST VERIFICATION - VER-2.

No

→ Go To 3

144

DRIVEABILITY - DIESEL

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the MAF Sensor harness connector.
Turn the ignition on.
Measure the voltage of the Sensor Reference Voltage A circuit.
Is the voltage above 4.8 volts?

All

Yes

→ Replace the Mass Air Flow Sensor.

Perform ROAD TEST VERIFICATION - VER-2.

No

→ Go To 4

4

Turn the ignition off.
Disconnect the Engine Oil Pressure Sensor harness connector.
Turn the ignition on.
Measure the voltage of the Sensor Reference Voltage A circuit.
Is the voltage above 4.8 volts?

All

Yes

→ Replace the Engine Oil Pressure Sensor.

Perform ROAD TEST VERIFICATION - VER-2.

No

→ Go To 5

5

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the MAF Sensor and Engine Oil Pressure Sensor harness connectors.
Measure the resistance between ground and the Sensor Reference Voltage A circuit.
Is the resistance above 100 kohms?

All

Yes

→ Go To 6

No

→ Repair the Sensor Reference Voltage A circuit for a short to

ground.
Perform ROAD TEST VERIFICATION - VER-2.

6

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the MAF Sensor harness connector.
Measure the resistance between the Sensor Reference Voltage A circuit and the MAF
Sensor Ground circuit.
Disconnect the Engine Oil Pressure Sensor harness connector.
Measure the resistance between the Sensor Reference Voltage A circuit and the
Engine Oil Pressure Sensor Ground circuit.
Is the resistance above 100 kohms for both measurements?

All

Yes

→ Go To 7

No

→ Repair the Sensor Reference Voltage A circuit for a short to the

Sensor Ground circuit that measured below 100 kohms.
Perform ROAD TEST VERIFICATION - VER-2.

7

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Fuel Pressure Sensor harness connector.
Measure the resistance between ground and the Fuel Pressure Sensor 5-Volt Supply
circuit.
Is the resistance above 100 kohms?

All

Yes

→ Go To 8

No

→ Repair the Fuel Pressure Sensor 5-Volt Supply circuit for a short

to ground.
Perform ROAD TEST VERIFICATION - VER-2.

145

DRIVEABILITY - DIESEL

P0641-SENSOR REFERENCE VOLTAGE A CKT VOLTAGE TOO LOW —

Continued

TEST

ACTION

APPLICABILITY

8

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Fuel Pressure Sensor harness connector.
Measure the resistance between the Fuel Pressure Sensor 5-Volt Supply circuit and
the Sensor Ground circuit.
Is the resistance above 100 kohms?

All

Yes

→ Go To 9

No

→ Repair the Fuel Pressure Sensor 5-Volt Supply circuit for a short

to the Sensor Ground circuit.
Perform ROAD TEST VERIFICATION - VER-2.

9

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

10

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

→ Repair as necessary.

Perform ROAD TEST VERIFICATION - VER-2.

No

→ Test Complete.

146

DRIVEABILITY - DIESEL

P0641-SENSOR REFERENCE VOLTAGE A CKT VOLTAGE TOO LOW —

Continued

 

 

 

 

 

 

 

Content   ..  1148  1149  1150  1151   ..