Chrysler Town, Dodge Caravan. Manual - part 1057

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1055  1056  1057  1058   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 1057

 

 

Symptom:

P0890-SWITCHED BATTERY

When Monitored and Set Condition:

P0890-SWITCHED BATTERY

When Monitored:

When the ignition is turned from the

9off9 position to the 9run9 position

and/or the ignition is turned from the

9crank9 position to the 9run9 position.

Set Condition:

This DTC is set if the Transmission Control Module (TCM) senses voltage

on any of the pressure switch inputs prior to the TCM energizing the relay. Note: Due to
the integration of the Powertrain and Transmission Control Modules, the transmission
part of the PCM has its own specific power and ground circuits.

POSSIBLE CAUSES

2/4 PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE

L/R PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE

OD PRESSURE SWITCH SENSE CIRCUIT SHORT TO VOLTAGE

POWERTRAIN CONTROL MODULE

INTERMITTENT WIRING AND CONNECTORS

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read Engine DTC’s. Check and repair all Engine DTC’s prior to

performing any transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Powertrain Control Module. Some problems are
corrected by software upgrades to the Transmission and Engine software.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

264

TRANSMISSION - NGC

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, Check the STARTS SINCE SET counter for P0890.

Note: This counter only applies to the last DTC set.
Is the

9STARTS SINCE SET9 counter set at 0?

All

Yes

→ Go To 3

No

→ Go To 7

3

Turn the ignition off to the lock position.
Disconnect the PCM harness connector.
Disconnect the Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and Transmission Control Relay
Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the voltage of the OD Pressure Switch Sense circuit.
Is the voltage above 0.5 volt?

All

Yes

→ Repair the OD Pressure Switch Sense circuit for a short to

voltage.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→ Go To 4

4

Turn the ignition off to the lock position.
Disconnect the PCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and Transmission Control Relay
Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the voltage of the 2/4 Pressure Switch Sense circuit.
Is the voltage above 0.5 volt?

All

Yes

→ Repair the 2/4 Pressure Switch Sense circuit for a short to voltage.

Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→ Go To 5

265

TRANSMISSION - NGC

P0890-SWITCHED BATTERY —

Continued

TEST

ACTION

APPLICABILITY

5

Turn the ignition off to the lock position.
Disconnect the PCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and Transmission Control Relay
Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the voltage of the L/R Pressure Switch Sense circuit.
Is the voltage above 0.5 volts?

All

Yes

→ Repair the L/R Pressure Switch Sense circuit for a short to

voltage.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→ Go To 6

6

Using the schematics as a guide, inspect the wiring and connectors. Repair as
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Powertrain Control Module per the Service Informa-
tion. WITH THE DRBIII

t PERFORM QUICK LEARN AND

REPROGRAM PINION FACTOR.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

7

The conditions necessary to set the DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring and connectors while checking for shorted and open circuits.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair as necessary.

Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→ Test Complete.

266

TRANSMISSION - NGC

P0890-SWITCHED BATTERY —

Continued

Symptom:

P0891-TRANSMISSION RLY ALWAYS ON

When Monitored and Set Condition:

P0891-TRANSMISSION RLY ALWAYS ON

When Monitored:

When the ignition is turned from the

9off9 position to the 9run9 position

and/or the ignition is turned from the

9crank9 position to the 9run9 position.

Set Condition:

This DTC set if the Transmission Control Module (TCM) senses greater

than 3 volts at the Transmission Control Relay Output circuits at the TCM prior to the
TCM energizing the relay. Note: Due to the integration of the Powertrain and Transmis-
sion Control Modules, the transmission part of the PCM has its own specific power and
ground circuits.

POSSIBLE CAUSES

TRANSMISSION CONTROL RELAY STUCK CLOSED

TRANSMISSION CONTROL RELAY CONTROL CIRCUIT SHORT TO VOLTAGE

TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT SHORT TO VOLTAGE

POWERTRAIN CONTROL MODULE

INTERMITTENT WIRING AND CONNECTORS

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read Engine DTC’s. Check and repair all Engine DTC’s prior to

performing any transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Powertrain Control Module. Some problems are
corrected by software upgrades to the Transmission and Engine software.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

267

TRANSMISSION - NGC

 

 

 

 

 

 

 

Content   ..  1055  1056  1057  1058   ..