Chrysler Town, Dodge Caravan. Manual - part 1023

 

  Index      Chrysler     Chrysler TOWN & COUNTRY, VOYAGER, Dodge Caravan - service repair manual 2001-2007 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1021  1022  1023  1024   ..

 

 

Chrysler Town, Dodge Caravan. Manual - part 1023

 

 

TEST

ACTION

APPLICABILITY

2

NOTE: The vehicle must be driven to set this DTC, the transmission must be
warm or hot with the Engine RPM above 1000 RPM.
This DTC is an indicator of a 2/4 and/or O/D Hydraulic Pressure Switch DTC’s
present. Perform the tests for P0870 and/or P0845 to determine which switch is
failing.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
If there are no possible causes remaining, view repair.

All

Repair

Refer to the Transmission category and perform the appropriate
symptom for P0870 and/or P0845.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

128

TRANSMISSION - EATX

P0992- 2-4/OD HYDRAULIC PRESSURE TEST FAILURE —

Continued

Symptom:

P1652-SERIAL COMMUNICATION LINK MALFUNCTION

When Monitored and Set Condition:

P1652-SERIAL COMMUNICATION LINK MALFUNCTION

When Monitored:

Continuously with engine running.

Set Condition:

The DTC sets in approximately 20 seconds if no BUS messages are

received by the TCM.

POSSIBLE CAUSES

NO COMMUNICATION WITH MIC

NO COMMUNICATION WITH PCM

INTERMITTENT WIRING AND CONNECTORS

TRANSMISSION CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, erase TCM DTC’s.

Note: Erase P0700 DTC in the PCM to turn the MIL light off after making
transmission repairs.
Start the engine in park.
Did the DTC reset after the engine was started?

All

Yes

→ Go To 2

No

→ Go To 5

2

Ignition on, engine not running.
With the DRBIII

t, attempt communication with the MIC

Can you communicate with the MIC?

All

Yes

→ Go To 3

No

→ Refer to the Communication category for the related symptom(s).

Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

3

Ignition on, engine not running.
With the DRBIII

t, select the following screens in order: 9BODY9 9MIC9 9MONITOR

DISPLAY

9 9PCI BUS ENGINE INFO9.

Does the DRBIII

t, read 9NO RESPONSE9 from any of the listed PCM monitors?

All

Yes

→ Refer to Communication Category for the related symptom(s).

Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Go To 4

129

TRANSMISSION - EATX

TEST

ACTION

APPLICABILITY

4

Using the schematics as a guide, inspect the wiring and connectors. Repair as
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIII

t PERFORM QUICK LEARN AND

REPROGRAM PINION FACTOR.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

5

The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorted and open circuits.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair as necessary.

Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Test Complete.

130

TRANSMISSION - EATX

P1652-SERIAL COMMUNICATION LINK MALFUNCTION —

Continued

Symptom:

P1684-BATTERY WAS DISCONNECTED

When Monitored and Set Condition:

P1684-BATTERY WAS DISCONNECTED

When Monitored:

Whenever the key is in the Run/Start position.

Set Condition:

This code is set whenever Transmission Control Module (TCM) is

disconnected from battery power B+ or ground. It will also be set during the DRBIII

t

Quick Battery Disconnect procedure.

POSSIBLE CAUSES

QUICK LEARN WAS PERFORMED

RECENT BATTERY DISCONNECTION

TCM WAS REPLACED OR DISCONNECTED

INTERMITTENT WIRING AND CONNECTORS

FUSED B+ CIRCUIT TO TCM OPEN

GROUND CIRCUIT OPEN

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many Transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing Transmission Symptom Diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

131

TRANSMISSION - EATX

 

 

 

 

 

 

 

Content   ..  1021  1022  1023  1024   ..