Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 715

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  713  714  715  716   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 715

 

 

When Monitored:
While the CAN bus ignition status is in IGN_RUN, the module checks the sensor input ranges.

Set Condition:
If the module detects a seat weight sensor input with the total seat weight below -6.5 kg +/- 1kg.

Possible Causes

DAMAGE TO THE PASSENGER SEAT STRUCTURE, RISER ASSEMBLY, CROSSMEMBERS, SEAT TRACKS,
FLOOR PAN

OBJECT UNDER SEAT OR REAR SEAT FOLDED DOWN AND RESTING AGAINST PASSENGER SEAT

OCCUPANT CLASSIFICATION MODULE (OCM)

Diagnostic Test

1.

TEST CONDITIONS

ACTIVE INTERNAL DTC

IGNITION DTC

BATTERY DTC

SEAT WEIGHT SENSOR DTC

NOTE: Ensure the battery is fully charged.

NOTE: When reconnecting Airbag system components, the ignition must be turned off and the battery must
be disconnected.
Turn the ignition on, then off, and then on again.

With the scan tool, read Occupant Classification Module (OCM) DTCs.

Does the scan tool display any active DTCs listed above?

Yes

>> Diagnose and repair the DTCs. Refer to the Table of Contents in this Section for a complete list of

symptoms.

No

>> Go To 2

2.

ACTIVE OR STORED DTC

With the scan tool, read OCM DTCs.

Does the scan tool display active: B1BBC-NEGATIVE SYSTEM WEIGHT?

Yes

>> Go To 3

No

>> Go To 4

3.

PERFORM OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST

Verify that the passenger seat is empty.

Perform a visual inspection of the Passenger Seat, wiring, connectors, risers, sensors, and retainers. Look for
chafed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or contaminated
terminals. Also, inspect for damaged or bent risers, a damaged or bent seat and seat structure, damaged or bent
seat tracks, and damaged or loose sensors. Repair or replace any problems found in accordance with the service
information and then continue this procedure. Refer to 23 - BODY/SEATS.

NOTE: Failure to follow the test instructions or aborting the test will cause faults to set when performing
the Occupant Classification Module System Verification Test. To prevent faults due to process errors: Verify
That All Tests Steps That Led You Here Were Performed As Directed; Verify That The Ignition Is In Run; Wait
30 Seconds After Changing The Seat Weight Before Proceeding To Allow The System To Stabilize; Only
Press Scan Tool Buttons When Directed To Do So; and Perform The Occupant Classification Module System
Verification Test To Completion.
With the scan tool in OCM, select More Options, select System Tests, and select Occupant Classification Module
System Verification Test. Run the test by following the instructions displayed on the scan tool. When the test is
complete, proceed as follows.

8O - 266

RESTRAINTS - ELECTRICAL DIAGNOSTICS

LX

With the scan tool, read OCM DTCs.

Does the scan tool display active: B1BBC-OCS NEGATIVE SYSTEM WEIGHT DTC?

Yes

>> Perform the *Diagnosis/Checkout Procedure For Seat Weight Sensors.

Perform OCS VERIFICATION TEST - VER 1.

No - But Other DTCs Present

Diagnose and repair the DTCs. Refer to the Table of Contents in this Section for a complete list of
symptoms.

No - No Active DTCs Present

Perform OCS VERIFICATION TEST - VER 1.

4.

STORED B1BBC-OCS NEGATIVE SYSTEM WEIGHT DTC

With the scan tool, record and erase all DTC’s from all Airbag System Modules.

If any ACTIVE codes are present they must be resolved before diagnosing any stored codes.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.

Look for chafed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or con-
taminated terminals.

The following additional checks may assist you in identifying a possible intermittent problem.

Reconnect any disconnected components and harness connector.

WARNING: To avoid personal injury or death, turn the ignition on, then reconnect the battery.
With the scan tool monitor active codes as you work through the following steps.

Wiggle the wiring harness and connectors of the related airbag circuit or component.

If codes are related to the Driver Airbag circuits, rotate the steering wheel from stop to stop.

IF only stored codes return continue the test until the problem area has been isolated.

In the previous steps you have attempted to recreate the conditions responsible for setting active DTC in question.

Are any ACTIVE DTC’s present?

Yes

>> Select appropriate symptom from Symptom List.

No

>> No problem found at this time. Erase all codes before returning vehicle to customer.

LX

RESTRAINTS - ELECTRICAL DIAGNOSTICS

8O - 267

B1BBD-OCM CURRENT CONFIGURATION TABLE UNPROGRAMMED

For a complete wiring diagram Refer to Section 8W.

When Monitored:
If the Configuration Table is not programmed at the supplier or when the checksum is invalid.

Set Condition:
This DTC will set if the module was received unprogrammed from the supplier, the vehicle line was not iden-
tified correctly or if the flash procedure was not completed successfully

Possible Causes

NEW OCCUPANT CLASSIFICATION MODULE

INTERNAL CHECKSUM FAILURE

Diagnostic Test

1.

MODULE CONFIGURATION

Does the scan tool display B1BBD-OCM CURRENT CONFIGURATION TABLE UNPROGRAMMED?

Yes

>> Perform the B1BA7–OCS VERIFICATION REQUIRED diagnostic procedure.

No

>> Replace the Occupant Classification Module in accordance with the service information.

With the scan tool, perform the OCM SYSTEM VERIFICATION procedure.

8O - 268

RESTRAINTS - ELECTRICAL DIAGNOSTICS

LX

B1BC7-DEPLOYMENT DATA RECORD FULL

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition on. The module’s on board diagnostics continuously performs internal circuit tests.

Set Condition:
This DTC will set if the module identifies an out of range internal circuit.

Possible Causes

OCCUPANT RESTRAINT CONTROLLER

Diagnostic Test

1.

CHECK FOR ACTIVE DTC

Turn the ignition on.

With the scan tool, read ORC DTCs.

Is the Deployment Data Record Full DTC active?

Yes

>> Go To 2

No

>> Perform the ORC VERIFICATION TEST-VER. 1.

2.

REPLACE THE OCCUPANT RESTRAINT CONTROLLER

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

WARNING: If the airbag control module is dropped at any time, it must be replaced. Failure to take the
proper precautions can result in accidental airbag deployment and personal injury or death.

View repair.

Repair

Replace the Occupant Restraint Controller in accordance with the service information.

Perform the ORC VERIFICATION TEST-VER 1.

LX

RESTRAINTS - ELECTRICAL DIAGNOSTICS

8O - 269

 

 

 

 

 

 

 

Content   ..  713  714  715  716   ..