Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 598

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  596  597  598  599   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 598

 

 

B1D1E,B1D2A–MIRROR VERTICAL MOTOR CONTROL CIRCUIT/PERFORMANCE –
DOOR MODULE

8N - 90

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

LX

For a complete wiring diagram Refer to Section 8W.

When Monitored:
Continuously.

Set Condition:
When the Memory Mirror Module senses a value below the tolerance of the mirror motor on the Mirror Vertical
Motor Control circuit for over 10 ms., this code will set.NOTE: This test covers both the Driver and Pas-
senger code depending on the side the code appeared in.

Possible Causes

(P71) OR (P72) MIRROR VERTICAL DRIVER CIRCUIT SHORT TO GROUND

(P71) OR (P72) MIRROR VERTICAL DRIVER CIRCUIT SHORTED TO THE (Z912) OR (Z911) GROUND
CIRCUIT

MIRROR SHORTED

DRIVER/PASSENGER DOOR MODULE

Diagnostic Test

1.

TEST FOR INTERMITTENT CONDITION

Turn the ignition on.

With the scan tool, record and erase DTC’s

Operate the Mirror Switch in all directions several times.

Cycle the ignition from on to off three times.

Turn the ignition on.

With the scan tool, read DTC’s.

Does the scan tool display B1D1E or B1D2A–MIRROR VERTICAL MOTOR CONTROL CIRCUIT/PERFOR-
MANCE?

Yes

>> Go To 2

No

>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-

matic as a guide, inspect the wiring and connectors.

Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1).

LX

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

8N - 91

2.

TEST FOR A SHORTED MIRROR

Disconnect the appropriate mirror connector.

With the scan tool, erase DTC’s.

Operate the Mirror Switch in all directions several times.

Cycle the ignition from on to off three times.

Turn the ignition on.

With the scan tool, read DTC’s.

Does the scan tool display B1D1E or B1D2A–MIRROR VERTI-
CAL MOTOR CONTROL CIRCUIT/PERFORMANCE?

No

>> Replace the Mirror.

Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1).

Yes

>> Go to 3

3.

TEST THE (P71) OR (P72) MIRROR VERTICAL MOTOR DRIVER WIRE FOR A SHORT TO GROUND

Turn the ignition off.

Disconnect the appropriate Door Module C4 connector.

Measure the resistance between ground and the (P71) or (P72) Mirror
Vertical Motor Driver circuit.

Is the resistance below 5000.0 ohms?

Yes

>> Repair the (P71) or (P72) Mirror Vertical Motor Driver circuit

for a short to ground.

Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1).

No

>> Go to 4

8N - 92

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

LX

4.

TEST THE (P71) OR (P72) MIRROR VERTICAL MOTOR DRIVER CIRCUIT SHORTED TO THE (Z912)
GROUND CIRCUIT.

Measure the resistance between the (P71) or (P72) Mirror Vertical
Motor Driver circuit and the (Z912) or (Z911) Ground circuit.

Is the resistance below 5000.0 ohms?

Yes

>> Repair the (P71) or (P72) Mirror Vertical Motor Driver circuit

for a short to the (Z912) or (Z911) Ground Circuit.

Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1).

No

>> Replace the appropriate Door Module.

Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1).

LX

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

8N - 93

 

 

 

 

 

 

 

Content   ..  596  597  598  599   ..