Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 594

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  592  593  594  595   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 594

 

 

B1D0C,B1D15–MIRROR VERTICAL POSITION SENSOR INPUT CIRCUIT LOW –
DOOR MODULE

8N - 74

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

LX

For a complete wiring diagram Refer to Section 8W.

When Monitored:
Continuously.

Set Condition:
When the Driver/Passenger Door Module senses a value below the parameter of the mirror sensor on the
Mirror Vertical Position Signal circuit for over 60 ms., this code will set.NOTE: This test covers both the
Driver and Passenger code depending on the side the code appeared in.

Possible Causes

(P67) OR (P64) MIRROR VERTICAL POSITION SIGNAL CIRCUIT SHORT TO GROUND

(P67) OR (P64) MIRROR VERTICAL POSITION SIGNAL CIRCUIT SHORTED TO (P69) OR (P66) MIRROR
SENSOR GROUND CIRCUIT

MIRROR SHORTED

DRIVER/PASSENGER DOOR MODULE

Diagnostic Test

1.

TEST FOR INTERMITTENT CONDITION

Turn the ignition on.

With the scan tool, record and erase DTC’s

Operate the Mirror Switch in all directions several times.

Cycle the ignition from on to off three times.

Turn the ignition on.

With the scan tool, read DTC’s.

Does the scan tool display B1D0C or B1D15–MIRROR VERTICAL POSITION SENSOR INPUT CIRCUIT
LOW?

Yes

>> Go To 2

No

>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-

matic as a guide, inspect the wiring and connectors.

Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1).

LX

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

8N - 75

2.

TEST FOR A SHORTED MIRROR

Disconnect the appropriate mirror connector.

With the scan tool, erase DTC’s.

Operate the Mirror Switch in all directions several times.

Cycle the ignition from on to off three times.

Turn the ignition on.

With the scan tool, read DTC’s.

Does the scan tool display B1D0C or B1D15–MIRROR VERTI-
CAL POSITION SENSOR INPUT CIRCUIT LOW?

No

>> Replace the Mirror.

Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1).

Yes

>> Go to 3

3.

TEST THE (P67) OR (P64) MIRROR VERTICAL POSITION SIGNAL WIRE FOR A SHORT TO GROUND

Turn the ignition off.

Disconnect the appropriate Door Module C4 connector.

Measure the resistance between ground and the (P67) or (P64) Mirror
Vertical Position Signal circuit.

Is the resistance below 5000.0 ohms?

Yes

>> Repair the (P67) or (P64) Mirror Vertical Position Signal cir-

cuit for a short to ground.

Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1).

No

>> Go to 4

8N - 76

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

LX

4.

TEST THE (P67) OR (P64) MIRROR VERTICAL POSITION SIGNAL CIRCUIT SHORTED TO THE (P69) OR
(P66) MIRROR SENSOR GROUND CIRCUIT.

Measure the resistance between the (P67) or (P64) Mirror Vertical Posi-
tion Signal circuit and the (P69) or (P66) Mirror Sensor Ground circuit.

Is the resistance below 5000.0 ohms?

Yes

>> Repair the (P67) or (P64) Mirror Vertical Position Signal cir-

cuit for a short to the (P69) or (P66) Sensor Ground Circuit.

Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1).

No

>> Replace the appropriate Door Module.

Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1).

LX

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

8N - 77

 

 

 

 

 

 

 

Content   ..  592  593  594  595   ..