Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 1962

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1960  1961  1962  1963   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 1962

 

 

b. If the transmission was completely overhauled or the torque converter was replaced or drained, add 8.1 L

(17.1 pts.) of transmission fluid to transmission.

4. Check the transmission fluid (Refer to 21 - TRANSMISSION/AUTOMATIC - NAG1/FLUID AND FILTER - STAN-

DARD PROCEDURE - CHECK OIL LEVEL) and adjust as required.

FLUID/FILTER SERVICE

1. Run the engine until the transmission oil reaches

operating temperature.

2. Raise and support vehicle.

3. Remove the bolts (5) and retainers (4) holding the

oil pan to the transmission.

4. Remove the transmission oil pan (3) and gasket (2)

from the transmission.

5. Remove the transmission oil filter (1) and o-ring

from the electrohydraulic control unit.

6. Clean the inside of the oil pan (3) of any debris.

Inspect the oil pan gasket (2) and replace if neces-
sary.

7. Install a new oil filter (1) and o-ring into the elec-

trohydraulic control unit.

8. Install the oil pan (3) and gasket (2) onto the trans-

mission.

9. Install the oil pan bolts (5) and retainers (4). Torque

the bolts to 8 N·m (70 in.lbs.).

10. Lower the vehicle and add 7.0 L (7.4 qts.) of

transmission fluid to the transmission.

11. Check the oil level (Refer to 21 - TRANSMIS-

SION/AUTOMATIC - NAG1/FLUID AND FILTER - STANDARD PROCEDURE - CHECK OIL LEVEL).

Fluid/Filter Service Points

1 - OIL FILTER
2 - OIL PAN GASKET
3 - OIL PAN
4 - RETAINER
5 - BOLT

21 - 382

AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION

LX

CLUTCH-FREEWHEELING

DESCRIPTION

Freewheeling clutches are installed in the front plane-
tary gear set between the sun gear and the stator
shaft, and in the rear planetary gear set between the
sun gear and the intermediate shaft.

The freewheel consists of an outer race (4), an inner
race (7), a number of locking elements (3) and a cage
(6) for these locking elements.

OPERATION

The freewheeling clutch optimizes individual gear-
shifts. They lock individual elements of a planetary
gear set together or against the transmission housing
in one direction of rotation to allow the torque to be
transmitted.

If the inner race (7) of the freewheeling clutch is
locked and the outer race (4) turns counter-clockwise
(1), the locking elements (3) adopt a diagonal position
on account of their special contours, allowing the free-
wheel function. The inner race (4) slides under the
locking elements (3) with minimal friction. If the rota-
tion of the outer race (4) changes to clockwise (2), the
locking elements (3) stand up and lock the outer and
inner races (4, 7) together.

LX

AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION

21 - 383

DISASSEMBLY

1. Remove retaining ring (5) from hollow shaft (1).

2. Remove rear sun gear (4) with the K3 internally toothed disk carrier and rear freewheeling clutch F2 (3).

3. Remove snap-ring (2) for freewheel.

4. Press freewheeling clutch (3) out of sun gear.

5. Check O-rings (6), replace if necessary.

Freewheeling Clutch F2

1 - HOLLOW SHAFT

4 - K3 INNER DISC CARRIER AND REAR PLANETARY SUN GEAR

2 - F2 CLUTCH SNAP-RING

5 - RETAINING RING

3 - FREEWHEELING CLUTCH F2

6 - O-RINGS

21 - 384

AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION

LX

6. Check the anti-friction bearing (2) in the rear plan-

etary sun gear for damage. Replace as necessary.

LX

AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION

21 - 385

 

 

 

 

 

 

 

Content   ..  1960  1961  1962  1963   ..