Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 1895

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1893  1894  1895  1896   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 1895

 

 

P1639-TCM INTERNAL-CAN 2 RAM PERFORMANCE

For a complete wiring diagram Refer to Section 8W

21 - 114

AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS

LX

Theory of Operation

The Transmission Control Module (TCM) performs various internal tests to verify proper controller operation. This
DTC indicates that there is an internal error with the controllers Random Access Memory (RAM) on the CAN con-
troller 2 section of the microprocessor. If detected, the controller will enter Limp-in mode and illuminate the MIL.

When Monitored:
Continuously with the ignition on.

Set Condition:
If the TCM detects an internal error with the controllers Random Access Memory (RAM) on the CAN controller
2 section of the microprocessor.

Possible Causes

TRANSMISSION CONTROL MODULE

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 21 - TRANSMIS-
SION/TRANSAXLE/AUTOMATIC - NAG1 - DIAGNOSIS AND TESTING)

Diagnostic Test

1.

TRANSMISSION CONTROL MODULE

View repair

Repair

Using the schematics as a guide, check the Transmission Control Module (TCM) terminals for corrosion,
damage, or terminal push out. Pay particular attention to all power and ground circuits. If no problems
are found, replace the TCM per the Service Information. (Refer to 8 - ELECTRICAL/ELECTRONIC
CONTROL MODULES/TRANSMISSION CONTROL MODULE - DESCRIPTION)

Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1. (Refer to 21 - TRANSMISSION/
TRANSAXLE/AUTOMATIC - NAG1 - STANDARD PROCEDURE)

LX

AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS

21 - 115

P1644-INCORRECT VARIANT/CONFIGURATION

For a complete wiring diagram Refer to Section 8W

21 - 116

AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS

LX

Theory of Operation

The Transmission Control Module (TCM) performs various internal tests to verify proper controller operation. If the
TCM detects that the variables that dictate the vehicle application are not present, the controller will enter Limp-in
mode and illuminate the MIL.

When Monitored:
Continuously with the ignition on.

Set Condition:
If the TCM detects that the variables that dictate the vehicle application are not present.

Possible Causes

CONTROLLER NOT CODED

TRANSMISSION CONTROL MODULE

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 21 - TRANSMIS-
SION/TRANSAXLE/AUTOMATIC - NAG1 - STANDARD PROCEDURE)

Diagnostic Test

1.

PERFORM TCM REPLACEMENT PROCEDURE

NOTE: Controller is programmed with generic software and will not allow the correct vehicle Powertrain
management.
With the scan tool, perform the TCM replacement procedure.

Were you able to update the controller successfully?

Yes

>> Test Complete.

Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1. (Refer to 21 - TRANSMISSION/
TRANSAXLE/AUTOMATIC - NAG1 - STANDARD PROCEDURE)

No

>> Using the schematics as a guide, check the Transmission Control Module (TCM) terminals for corrosion,

damage, or terminal push out. Pay particular attention to all power and ground circuits. If no problems
are found, replace the TCM per the Service Information. (Refer to 8 - ELECTRICAL/ELECTRONIC
CONTROL MODULES/TRANSMISSION CONTROL MODULE - DESCRIPTION)

Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1. (Refer to 21 - TRANSMISSION/
TRANSAXLE/AUTOMATIC - NAG1 - STANDARD PROCEDURE)

LX

AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS

21 - 117

 

 

 

 

 

 

 

Content   ..  1893  1894  1895  1896   ..