Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 1529

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1527  1528  1529  1530   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 1529

 

 

25. Push the camshaft (5) out of the back of the cyl-

inder head approximately 3.5 inches and remove
the right cam gear.

26. Remove the inner timing cover to cylinder head

retaining bolts.

27. Remove the cylinder head bolts in REVERSE of

tightening sequence.

28. Remove the cylinder head.

29. Clean and inspect all mating surfaces.

LEFT CYLINDER HEAD

1. Perform the fuel relief procedure.

2. Disconnect the negative battery cable.

3. Drain cooling system (Refer to 7 - COOLING -

STANDARD PROCEDURE).

4. Remove the upper intake manifold.

5. Remove the lower intake manifold (Refer to 9 -

ENGINE/MANIFOLDS/INTAKE

MANIFOLD

-

REMOVAL).

6. Remove the accessory drive belt (6).

7. Remove the belt tensioner (1).

8. Remove the accessory drive idler pulley.

9. Remove the power steering mounting bolts and set

pump (2) aside.

10. Remove the crankshaft damper (4) (Refer to 9 -

ENGINE/ENGINE BLOCK/VIBRATION DAMPER -
REMOVAL.

11. Remove the lower outer timing belt cover.

12. Raise and support the vehicle.

9 - 2140

ENGINE - 3.5L - SERVICE INFORMATION

LX

13. Remove the front exhaust pipe to exhaust mani-

fold mounting nuts (2).

14. Disconnect both oxygen sensor harness connec-

tors (1,2).

15. Lower the vehicle.

16. Remove the outer timing belt cover (Refer to 9 - ENGINE/VALVE TIMING/TIMING BELT / CHAIN COVER(S) -

REMOVAL).

TIMING GEAR ALIGNMENT

1 - RIGHT CAMSHAFT GEAR ALIGNMENT MARK

7 - LEFT CAMSHAFT GEAR

2 - RIGHT CAMSHAFT GEAR

8 - LEFT CAMSHAFT GEAR ALIGNMENT MARK

3 - CYLINDER HEAD TO INNER TIMING BELT COVER BOLTS -
RIGHT

9 - CRANKSHAFT GEAR ALIGNMENT MARK

4 - TIMING BELT

10 - CRANKSHAFT GEAR

5 - WATER PUMP PULLEY

11 - TIMING BELT TENSIONER PULLEY

6 - CYLINDER HEAD TO INNER TIMING BELT COVER BOLTS -
LEFT

12 - TIMING BELT TENSIONER

LX

ENGINE - 3.5L - SERVICE INFORMATION

9 - 2141

17. Rotate the engine to TDC and align the timing marks (1,8,9).

18. Remove the timing belt tensioner (12), timing belt (4), then reset tensioner. (Refer to 9 - ENGINE/VALVE TIM-

ING/TMNG BELT/CHAIN TENSIONER&PULLEY - REMOVAL)

19. Remove the left cylinder head cover to cylinder

head ground strap (3).

20. Remove the left cylinder head cover.

21. Remove the left rocker arm assembly (2).

9 - 2142

ENGINE - 3.5L - SERVICE INFORMATION

LX

22. Remove the left camshaft thrust plate (1).

23. Counterhold the left cam gear and remove the

cam gear retaining bolt. (Refer to 9 - ENGINE/
VALVE

TIMING/TIMING

BELT/CHAIN

AND

SPROCKETS - REMOVAL)

24. Push the camshaft out of the back of the cylinder

head approximately 3.5 inches and remove the
cam gear.Remove the front timing belt housing to
cylinder head bolts.

25. Remove the cylinder head bolts in REVERSE of

tightening sequence.

26. Remove the cylinder head.

27. Clean and inspect all mating surfaces.

.

LX

ENGINE - 3.5L - SERVICE INFORMATION

9 - 2143

 

 

 

 

 

 

 

Content   ..  1527  1528  1529  1530   ..