Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 1348

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1346  1347  1348  1349   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 1348

 

 

5.

(F858) EXHAUST GAS PRESSURE SENSOR 5 VOLT SUPPLY CIRCUIT OPEN OR HIGH RESISTANCE

Measure the resistance of the (F858) Exhaust Gas Pressure Sensor 5
Volt Supply circuit between the Exhaust Gas Pressure Sensor connec-
tor and the Engine Control Module (ECM) connector.

Is the resistance below 10.0 ohms?

Yes

>> Go to 10

No

>> Repair the (F858) Exhaust Gas Pressure Sensor 5 Volt

Supply circuit for an open circuit or high resistance.

Perform the ECM Verification Test Ver. 1. (Refer to 9 -
ENGINE - DIAGNOSIS AND TESTING)

6.

EXHAUST GAS PRESSURE SENSOR

Turn the ignition on.

With the scan tool, Clear DTCs.

With the scan tool, select View DTCs.

NOTE: The scan tool should display an Exhaust Gas Pressure Sensor high voltage or open DTC with the
Exhaust Gas Pressure Sensor connector disconnected.

Does the scan tool display the DTC(s) as described above?

Yes

>> Replace the Exhaust Gas Pressure Sensor in accordance with the Service Information.

Perform the ECM Verification Test Ver. 1. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)

No

>> Go to 7

7.

(K35) EXHAUST GAS PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND

Turn the ignition off.

Disconnect the Engine Control Module (ECM) connector.

Measure the resistance between ground and the (K35) Exhaust Gas
Pressure Sensor Signal circuit in the Exhaust Gas Pressure Sensor
connector.

Is the resistance above 10.0 ohms?

Yes

>> Go to 8

No

>> Repair the (K35) Exhaust Gas Pressure Sensor Signal cir-

cuit for a short to ground.

Perform the ECM Verification Test Ver. 1. (Refer to 9 -
ENGINE - DIAGNOSIS AND TESTING)

9 - 1416

ENGINE ELECTRICAL DIAGNOSTICS - DIESEL

LX

8.

(K35) EXHAUST GAS PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO (K934) EXHAUST GAS
PRESSURE SENSOR GROUND CIRCUIT

Measure the resistance between the (K35) Exhaust Gas Pressure Sen-
sor Signal circuit and the (K934) Exhaust Gas Pressure Sensor Ground
circuit in the Exhaust Gas Pressure Sensor connector.

Is the resistance above 5.0 ohms?

Yes

>> Go to 9

No

>> Repair the (K35) Exhaust Gas Pressure Sensor Signal cir-

cuit for a short to the (K934) Exhaust Gas Pressure Sensor
Ground circuit.

Perform the ECM Verification Test Ver. 1. (Refer to 9 -
ENGINE - DIAGNOSIS AND TESTING)

9.

(K35) EXHAUST GAS PRESSURE SENSOR SIGNAL CIRCUIT OPEN OR HIGH RESISTANCE

Measure the resistance of the (K35) Exhaust Gas Pressure Sensor Sig-
nal circuit between the Exhaust Gas Pressure Sensor connector and
the Engine Control Module (ECM) connector.

Is the resistance below 5.0 ohms?

Yes

>> Go to 10

No

>> Repair the (K35) Exhaust Gas Pressure Sensor Signal cir-

cuit for an open circuit or high resistance.

Perform the ECM Verification Test Ver. 1. (Refer to 9 -
ENGINE - DIAGNOSIS AND TESTING)

LX

ENGINE ELECTRICAL DIAGNOSTICS - DIESEL

9 - 1417

10.

ENGINE CONTROL MODULE (ECM)

Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Exhaust Gas Pres-
sure Sensor and the Engine Control Module (ECM).

Look for any chafed, pierced, pinched, or partially broken wires.

Look for broken, bent, pushed out or corroded terminals.

Monitor the scan tool data relative to this circuit and wiggle test the wiring and connectors.

Look for the data to change or for the DTC to reset during the wiggle test.

Refer to any Technical Service Bulletins that may apply.

Were any problems found?

Yes

>> Repair as necessary.

Perform the ECM Verification Test Ver. 1. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)

No

>> Replace the Engine Control Module (ECM) in accordance with the Service Information.

Perform the ECM Verification Test Ver. 1. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)

9 - 1418

ENGINE ELECTRICAL DIAGNOSTICS - DIESEL

LX

P0473-EXHAUST PRESSURE SENSOR 1 HIGH

For a complete wiring diagram Refer to Section 8W

LX

ENGINE ELECTRICAL DIAGNOSTICS - DIESEL

9 - 1419

 

 

 

 

 

 

 

Content   ..  1346  1347  1348  1349   ..